manualshive.com logo in svg

ALTAI A3-Ei, Installation Manual

Share
Download
ALTAI A3-Ei Installation Manual Download Page 17

 

11 

Altai Technologies Ltd. All rights reserved 

 

Altai A3-Ei Dual-band 3x3 802.11ac Wi-Fi Access Point 

Installation Guide 

3.

 

Grounding Protection 

It is essential to properly ground all equipment to prevent the A3-Ei from 
the  electrical  damage  and  possible  electric  hazer  due  to  non-proper 
power  grounding.  Failure  to  do  so  may  result  in  equipment  damage, 
injury  or  death. 

Product  warranty  does  not  cover  damage  resulting  in 

part or in whole from improper grounding

.  An external grounding wire 

must  be  installed,  especially  when  A3-Ei  is  deployed  on  a  non-metal 
pole  or  the  metal  pole  is  not  properly  grounded.  Please  consult  your 
location’s  building  and  electrical  codes  and  follow  them,  or  consult 
standards such as National Electric Code. 
Use a 

10 AWG

 grounding wire to connect to the ground connector of 

the  A3-Ei  by  screw  driver.  Secure  the  grounding  screw  tight  and  the 
strap connects to the ground. 
It is recommended that the A3-Ei Dual-band 3x3 802.11ac Wi-Fi Access 
Point  should  be  installed  with  lightning  rod  to  avoid  any  potential 
electrical damage and to be connected with the ground node to the 
existing  ground.  Proper  grounding  will  always  be  the  safety 
consideration for the A3-Ei Dual-band 3x3 802.11ac Wi-Fi Access Point. 

 

Note: Grounding kits are not provided in the package

 

 

4.

 

Surge Protection 

Type  of  Ethernet  cable  in  outdoor  deployment  is  critical.  The  Ethernet 
cable should be either CAT 5e or CAT 6, outdoor rated, and shielded. 
Specifically,  the  following  types  of  Ethernet  cable  should  be  used  for 
outdoor  installation: 

screened  fully  shielded  twisted  pair  (sFTP)  cable, 

foiled twisted pair (FTP) cable, or shielded twisted pair (STP) cable

. 

UTP  Ethernet  cable  and/or  unshielded  RJ-45  jack

  are  not 

recommended  in  outdoor  deployment  due  to  increasing 
electromagnetic  noise  level.  Furthermore,  using  shielded  Ethernet 
cable with unshielded RJ45 jack between the A3-Ei and PoE injector is 
not recommended. Improperly grounded STP Ethernet cable acts as a 
magnet  for  static  surges  presented  in  the  environment.  Since  the 
charges discharged improperly, it couples with the data lines or power 
lines  of  the  PoE  cable.  As  a  result,  the  coupling  high  voltages  which 
presents on the PoE cable may damage the access point. Therefore, it 

Summary of Contents for A3-Ei

























Reviews:

No comments

Brands by name

Popular brands

Load more brands