manualshive.com logo in svg

Alpine PSS-31GM, Installation Manual, Page: 22 / 31

Share
Download
Alpine PSS-31GM Installation Manual Download Page 22

Chevrolet/GMC

FULL SIZE TRUCK 

˜

 22/31

AMPLIFIER InSTALLATIon

Installing Amplifier Bracket

 

A rivet nut tool is required for this installation 

(not included).

1

  Position the amplifier bracket to the rectangular 

opening below the center child seat restraint anchor 
as shown.

2

  Mark the rivet nut locations with a punch tool.  

Ensure the bracket is aligned top and bottom before marking the 

holes.

3

  Remove the Amplifier bracket and use a 25/64” 

(10mm) drill bit, drill 4 holes in the vehicle for the 
rivet nuts.

4

  Clean any metal shavings and sharp edges after 

drilling.

5

  Install the M6 rivet nuts per tool manufacturer’s 

procedure.

6

  Install the amplifier bracket to the vehicle using 

Screw Kit D (Amplifier Bracket Mounting Kit) apply 
the washer, lock washer and secure using the 
11mm bolt.

Installing Amplifier

1

  Hang the amplifier to the bracket tabs as shown.

2

  Mount the amplifier by lifting up and use the 

supplied (4) M4 pan head phillip screws from Screw 
Kit D (Amplifier Bracket Mounting Kit) to secure the 
amplifier bracket to the vehicle.

Summary of Contents for PSS-31GM
































Reviews:

No comments