manualshive.com logo in svg

Alpine i509-WRA-JL, Installation Manual, Page: 28 / 29

Share
Download
Alpine i509-WRA-JL Installation Manual Download Page 28

Jeep Wrangler

i509-WRA-JL

20220401v1

˜

 28/29

Set Up Guide

1

 

Turn the vehicle’s Ignition switch to ACC.

2

 

Turn ON the i509-WRA-JL by pressing any key.

3

 

Select the user language and press OK.

4

  To get into the settings the parking brake sequence needs to be done. 

Engage the parking brake, release

the parking brake, and engage the parking brake again.

5

 

Vehicle information- Set the desired gauge information. (HOME/VEHICLE INFO/SETUP).

6

 

To turn on rear camera in the system menu. (HOME/FUNCTION/CAMERA/REVERSE CAMERA).

7

 

If the vehicle is equipped with the factory accessory switches set those up. See page 27 for details. (MENU/
FACTORY SYSTEM SETUP/MAESTRO MODULE/VEHICLE FEATURES/AUX SWITCHES).

8

 

For vehicles with an OEM amplifier the Time Correction, P-EQ, and X-Over must be set flat. (HOME/UPPER
CENTRAL BUTTON ON SCREEN).

Troubleshooting Guide

Symptom

Possible Cause

Remedy

1

iPhone not working with 
HDMI.

Not using Apple HDMI to Lightning 
adapter. 

Purchase the HDMI to Lightning adapter 
directly from Apple. Not all 3rd party 
adapters work the same.

Didn’t plug USB power into a 2A 
source.

A 2A USB power source must be used to 
power on the device.

2

Android phone is not working 
with HDMI.

Using incorrect HDMI adapter.

If the phone has the feature to use an HDMI 
adapter it must be the one purchased from 
the manufacturer of the phone, not a third 
party adapter. 

Miracast or HDMI adapter isn’t 
plugged into a 2A source.

A 2A USB power source must be used to 
power on the device.

Miracast adapter has resolution 
settings that are too high.

Plug the adapter into another monitor (for 
example a television in the home) and reduce 
the resolution settings.

3

iDatalink website says serial 
number is invalid.

Incorrect serial number is being 
used.

In the i509-WRA-JL settings confirm the 
serial number. MENU/SETUP/GENERAL/
ABOUT.

Serial number may not be in 
iDatalink database.

Call ADS at 1-866-427-2999 and verify.

4

Headunit will not turn on.

Incorrect serial number was used 
when flashing maestro.

Flash Maestro with correct serial number.

4 pin Maestro data cable is 
disconnected or damaged.

Check for proper connection or 
disconnected pins.

OBD2 cable is not plugged in.

Connect OBD2 connector to the OBD2 port.

Monitor, key-harness or main 
harness are not connected.

Check for proper connection or 
disconnected pins.

Summary of Contents for i509-WRA-JL






























Reviews:

No comments