Alpha E-Tec 33 Installation And Commissioning Instructions Download Page 4

Page: 4 / 40

3 TECHNICAL DATA

3.1 TECHNICAL PERFORMANCE DATA E-TEC 33 HYBRID BOILER

Alpha E-Tec Hybrid - Technical Data

Domestic hot water maximum heating power

kW (kcal/h)

28.8 (24.773)

Central heating maximum heat input

kW (kcal/h)

24.6 (21.194)

DHW maximum useful heat output

kW (kcal/h)

28.3 (24.295)

CH maximum useful heat output

kW (kcal/h)

24.1 (20.717)

Minimum nominal heat input

kW (kcal/h)

4.5 (3.862)

Minimum nominal heat output

kW (kcal/h)

4.3 (3.689)

Efficiency at 100% Pn (80/60°C)

97.8

Efficiency at 30% of the load (80/60°C)

102.3

Efficiency at 100% Pn (50/30°C)

106.1

Efficiency at 30% of the load (50/30°C)

108.3

Efficiency at 100% Pn (40/30°C)

108.2

Efficiency at 30% of the load (40/30°C)

108.3

Room central heating seasonal efficiency (η

)

% 93

Water heating energy efficiency (η

)

% 87

Central heating circuit

Adjustable central heating temperature (min. / max)

°C

min. 20 - 50 / max 85

System max. working temperature

°C

System max. working pressure

bar

System expansion vessel nominal/(real) capacity

litres

8.0 / (5.8)

System expansion vessel factory-set pressure

bar

1.0

Minimum design system flow rate

L/h

500

Head with 1000 l/h flow rate

kPa (m c.a.)

40.6 (4.1)

Minimum system water content

litres

DHW circuit

Hot water production useful heat output

kW (kcal/h)

28.3 (24.295)

DHW adjustable temperature

°C

30 - 60

Domestic hot water circuit min. dynamic pressure

bar

0.3

Domestic hot water circuit / DHW Circuit max. pressure

bar

D.H.W. min. withdrawal

litres/min

1.5

Flow rate in continuous service (

∆

T 30°C)

litres/min

13.7

Gas supply

Gas flow rate at METHANE burner (G20)

MIN - MAX

0.48 - 2.61 (3.06 DHW)

Gas flow rate at LPG burner (G31)

MIN - MAX

kg/h

0.35 - 1.91 (2.25 DHW)

Electric power supply

V/Hz

230 - 50

Nominal power absorption

0.60

Installed electric power

Power absorbed by pump max speed

Power absorbed in stand-by

Electric insulation rating

X5D

Water content

litres

2.2

Empty condensation unit weight

33.6

Effective efficiency at 100% output

>93+2·log Pn

(Italian Lgs. D. 192/05 as amended)

(Pn = 24.1 kW)

Summary of Contents for E-Tec 33









































Search results

Summary of Contents for E-Tec 33

Reviews:

Related manuals for E-Tec 33

Brands by name

Popular brands

Alpha E-Tec 33, Installation And Commissioning Instructions

Search results

Summary of Contents for E-Tec 33

Reviews:

Related manuals for E-Tec 33

Brands by name

Popular brands