manualshive.com logo in svg

Alpego SKAT K1 5-250, Use And Maintenance Manual, Page: 16 / 24

Share
Download
Alpego SKAT K1 5-250 Use And Maintenance Manual Download Page 16

MANUALE SKAT K1 - K2 

Old Cod.D08974 

New Cod. MANT2010/00722 R.9 

 

 

INSTALLATION

 - 12 

Copyright ©2009 della Alpego spa® - All rights are reserved. Reprinting or unauthorized use of this manual is strictly forbidden without written permission by Alpego spa

 

 

4.7. HYDRAULIC CONNECTIONS TO THE TRACTOR  

The good performance of the implement depends largely from its  correct use  and from a regular maintenance program. 
It  is  therefore  advisable  to  follow  carefully  what  is  described  in  order  to  prevent  any  trouble  which  may  impair  the 
performance  of  the  machine  and  shorten  its  lifespan.  It  is  also  important  to  comply  with  the  rules  contained  in  this 
manual,  since  the  Manufacturer  disclaims  all  responsibility  for  damages  due  to  negligence  or  the  non-observance  of 
said rules. 

1.  Connect the quick-plug of  the hydraulic circuit to a socket of the tractor  

( a pressure between 160/190 bar is required);

 

 

 

 

 

2.  Gradually put the hydraulic system under pressure  - shown by  the manometer - 

until the working pressure  necessary for your  particular  type of soil  is reached  

Suggested pressure = 80/100 bar (see chart 5.5)  

 

 

 

 

 

               Remove the two pins from the side shaft support B and place  
               them in their correct place in the tractor connections A 

                 

 

 

 

 

Summary of Contents for SKAT K1 5-250

























Reviews:

No comments