Alpego SKAT K1 5-250 Use And Maintenance Manual Download Page 10 | Manualshive

Page: 10 / 24

Alpego SKAT K1 5-250 Use And Maintenance Manual Download Page 10

MANUALE SKAT K1 - K2

Old Cod.D08974

New Cod. MANT2010/00722 R.9

SAFETY REGULATIONS

- 6

Copyright ©2009 della Alpego spa® - All rights are reserved. Reprinting or unauthorized use of this manual is strictly forbidden without written permission by Alpego spa

3.7. SAFETY SIGNS

A good number of labels on the machine point out the sources of danger. Observe them carefully and follow the indications for a
safe use of the machine. These stickers should be kept clean and legible; if damaged they should be replaced.

LABEL

code

INDICATION

D02612

It is a MUST to read the user and
maintenance manual and safety
instructions before using the
equipment. These must be followed
during use.

D02627

Indicates hooking point for machine
transportation

D02613

Indicates the danger of shearing while
machine is working

D02617

Indicates where the supporting leg
should be positioned when the
machine is not being used. This
guarantees stability.

D02615

Indicates the need to switch off the
tractor and remove the ignition key
during maintenance operations

D02624

Indicates danger caused by
pressurised oil should the hydraulic
pipes break. Consult the instruction
manual before repairing hydraulic
systems.

D08148

Indicates the position of the safety pin
onto shank supports. The pin should
be placed in position A when the
hydraulic system is pressurised and
the machine is working. The pin
should be placed in position B when
the hydraulic system is no longer
pressurised and the machine is not
working.

D08477

Indicates the pressure setting of
the hydraulic system and the
corresponding accumulator
pressure. The hydraulic system is
standard set at 80 bar, the
accumulator at 60 bar

Q15A00531

The sticker depicts the compulsory
PPE (Personal Protective
Equipment): coverall, mask,
earplugs, safety shoes, gloves

«
...
8
9
10
11
12
...
»

Summary of Contents for SKAT K1 5-250

























Reviews:

No comments