manualshive.com logo in svg

Alpego SKAT K1 5-250, Use And Maintenance Manual, Page: 11 / 24

Share
Download
Alpego SKAT K1 5-250 Use And Maintenance Manual Download Page 11

MANUALE SKAT K1 - K2 

Old Cod.D08974 

New Cod. MANT2010/00722 R.9 

 

 

INSTALLATION

 - 7 

Copyright ©2009 della Alpego spa® - All rights are reserved. Reprinting or unauthorized use of this manual is strictly forbidden without written permission by Alpego spa

 

 

 

4. INSTALLATION 

4.1. LIFTING 

The machine should be lifted and transported with the right means, suitable for its weight, and by personnel trained in this kind of 
work. 

Hook the machine in the two points indicated in the figure below and go ahead.  The loads should not be raised by 
more than 200 mm from the ground while carrying out these operations. 
                                                                                                                     
                                                                                                                                    Machine ready for shipment 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

4.2. PREPARATION BEFORE USE 

Should the machine be delivered in a “ready for shipment” position (see section 4.1), please proceed as follows:  

1)  Remove the shanks from the group support assembled on the frame and place them in the correct position on the shank 

support.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Shanks on the group support 

Summary of Contents for SKAT K1 5-250

























Reviews:

No comments