almando Masterplay Installation Manual Download Page 4

SAFETY INSTRUCTIONS 

 
  

 

Connect the device to the power supply using the supplied power cord. 
A damaged cable must not be repaired. 

The operating voltage must match the local mains voltage. 

 

Protect the device from moisture and water. Do not operate the unit in 
rain.  The  appliance  must  not  be  operated  near  water,  bathtub,  sink, 
kitchen sink, wet room, swimming pool or damp rooms. Do not place 
objects filled with liquid, such as vases, glasses, bottles, etc. on top of 
the device. 

Avoid direct exposure to the sun as well as the immediate proximity of 
radiators, radiant heaters or similar devices. 
 
If  the  appliance  is  suddenly  brought  from  a  cold  to  a  warm  place, 
condensation may form inside the appliance. Before switching on, wait 
until the device has reached room temperature. 

To  protect  the  device  during  a  thunderstorm  or  when  it  is  not 
supervised or used for an extended period, the mains plug should be 
pulled. This prevents damage to the device due to lightning strikes and 
voltage surges in the power supply system. 

In  case  of  improper  use  and  by  opening  the  device,  the  guarantee 
claim will be extinguished!. 

 

Disclaimer of liability: 

almando  GmbH  is  not  liable  for  damage  to  equipment  caused  by 
negligence or improper use. In particular, almando GmbH is not liable 
for  loss  of  profit  or  other  assets  of  the  buyer.  This  restriction  also 
applies  to  the  personal  liability  of  employees,  representatives  and 
vicarious agents..

 

 

Summary of Contents for Masterplay

















Reviews: