background image

POEGE24T2SFP User Manual 

Alloy Computer Products Pty Ltd Copyright ©2014 

1. Introduction 

The POEGE24T2SFP is an unmanaged low cost Gigabit Ethernet Power Over Ethernet switch. 
The switch consists of 24x 10/100/1000Mbps PoE ports plus 2x 1000Mb SFP Ports. All copper 
ports are auto sensing, auto MDI/X ports allowing easy connectivity to your existing 
switching infrastructure and your PD PoE devices, such as IP Phones, Wireless Access Points 
and IP Video Cameras. All ports support up to 30W of power, with the switch supporting 
10.8W per port at full load. The POEGE24T2SFP supports up to 260W in total. 
 
With support for IEEE 802.3az Energy Efficient Ethernet (EEE) the switch can reduce power 
consumption by detecting the length of the cable and the operating load of the switch and 
automatically adjust the signal intensity, reducing energy consumption and helping reduce 
carbon emissions. 
  
The POEGE24T2SFP is the ideal solution for adding low cost PoE capability to your newly 
deployed IP PBX and IP Phone infrastructure.

 

Features 
 

 

Supports PoE power up to 30W for each PoE port  

 

Supports PoE power up to 260W for all PoE ports 

 

Supports PoE IEEE802.3at/af compliant PDs 

 

Supports IEEE802.3x flow control for Full-duplex Mode and backpressure for Half-
duplex Mode 

 

Supports IEEE802.3az energy efficient Ethernet (EEE), 

 

16K MAC address with auto-learning and auto-aging 

 

LED indicators for monitoring power, link, activity and speed 

 

2x SFP Ports for fibre up links to your existing switching infrastructure 

 

2. Checklist 

 

Before you start installing your equipment, verify that the package contains the following: 
 

 

The POEGE24T2SFP – Gigabit POE Switch  

 

Rack Mount kit with appropriate mounting screws 

 

Power Cable 

 

Paper Insert 
  

Please notify your supplier immediately if any of the aforementioned items are missing or 
damaged. 

 

 

 

 

 

 
 
 

 

Summary of Contents for POEGE24T2SFP














Reviews: