manualshive.com logo in svg

Allnet ALL168207, Quick Setup Manual

Share
Download
Allnet ALL168207 Quick Setup Manual Download Page 10

ALL168207 Coaxial Network Adapter

 

©

 2008. All rights reserved.                                                                                                        Page 10 

LEDs 

 

 

 

 

 

 

 

 

 

 

Power 

On: Power on 
Blinking: Standby mode (*1) 
Off: Power off 

COAX/ACT 

On: Coaxial Link detected and no traffic   
Blinking: Coaxial traffic detected   

 

Green: The Coaxial connection quality is good 

 

Orange: The Coaxial connection quality is fair 

 

Red: The Coaxial connection quality is bad 

Off: No Coaxial Link detected 

ETH/ACT 

On: Ethernet Link Detected 
Blinking: Ethernet traffic detected 
Off: No Ethernet Link detected 

*1 : 

The 

“Power“ LED indicator will blink in standby mode. It will get into standby mode, if you plug the 

device to outlet and no Ethernet link detected after booted and 60 second later. If you unplug the 
Ethernet cable, it will get into standby mode after 60 seconds. 

Under standby mode, COAX/ACT 

and ETH/ACT LEDs will both be off.

 

 

 

Summary of Contents for ALL168207













Reviews:

No comments

Brands by name

Popular brands

Load more brands