manualshive.com logo in svg

Allnet ALL02800N, Manual, Page: 6 / 83

Share
Download
Allnet ALL02800N Manual Download Page 6

 

    

ALL02800N 300M Wireless-N Accesspoint 

6

 

 

 

 

  

  

    

1.1  Features  

  

Complies with IEEE802.11n (Draft 2.0),  

IEEE802.11b and IEEE802.11g standards  

  

Supports five working modes: wireless AP,  

Repeater, P2P, P2MP and wireless client  

  

Provides 300Mbps receiving rate and 300Mbps  

sending rate       

  

MIMO technology utilizes reflection signal to  

increase 8 times transmission distance of original 802.11g
standard and reduces the "dead spots" in the wireless
coverage area                                     

  

Provides one Gigabit Auto-negotiation RJ45 port  

for LAN connection  

  

Supports two power supply ways: Power over  

Ethernet and external power adapter   

  

Supports SNMP and Web-based management  

interface  

  

Supports 64/128bit WEP encryption  

  

Supports multiple encryption methods as WPA,  

WPA2 and WPA&WPA2 and security mechanism  

  

Supports WPS (PBC and PIN) encryption method  

to free you from remembering long passwords  

  

Supports five connection modes: AP, WDS P2P  

  

  

  

  

Summary of Contents for ALL02800N




















































































Reviews:

No comments