20
3.2.3 Configure the AP as a Router with dynamic IP
address Ethernet
Configure TCP/IP parameters
1. Click
Advanced
Config
,
select
Bridging
,
and then click
Disable
for
Bridge Function
as shown in
Figure 3-4
. After that, click
FINISH
at
the bottom of this page to complete the modification of this page.
2. Click
Basic Config
,
select
Interface
(as shown in
Figure 3-7
),
in this
page, you can click radio button and enter
MODIFY
to choice which
interface that you want to change it (as shown in
Figure 3-8
).
In interface 1, Make sure this wireless interface status is
Active
, enter
the
Wireless interface IP
(
default is 192.168.1.1
) and
Wireless
interface Net Mask
(
default is 255.255.255.0
) that are suitable for
your wireless network.
In interface 2, Make sure this Ethernet interface status is
Active
, and
other parameters will obtain automatically by DHCP from your network
environment.
Click the
OK
button to return to the
Interface Parameter
window.
Finally, you need to click
FINISH
at the bottom of this page to complete
the modification of this page.
Hint1: Make sure interface 3 and 4 within status:
Disable
.
Hint2: In order to enable NAT service, choice the
NAT (PAT)
in the
interface Wireless and Ethernet. For example, make sure
Ethernet interface within
NAT (PAT)
On
and Wireless
interface is
NAT (PAT)
Off
, it means that every
communication through the Ethernet interface needs to do
NAT transfer.
3. Click
Basic Config
,
select
DHCP
(as shown in
Figure 3-10
)
and apply
the DHCP client service running on interface 2 (Ethernet interface),
After that, click
FINISH
at the bottom of this page to complete the
modification of this page.
21
3.2.4 Configure the AP as a Router with static IP address
Ethernet
Configure TCP/IP parameters
1. Click
Advanced Config
,
select
Bridging
,
and then click
Disable
for
Bridge Function
as shown in
Figure 3-4
. After that, click
FINISH
at
the bottom of this page to complete the modification of this page.
2. Click
Basic Config
,
select
DHCP
(as shown in
Figure 3-10
)
and make
sure the DHCP client service is
Disable
. After that, click
FINISH
at the
bottom of this page to complete the modification of this page.
3. Click
Basic Config
,
select
Interface
(as shown in
Figure 3-7
),
In this
page, you can click radio button and enter
MODIFY
to choice which
interface that you want to change it(as shown in
Figure 3-8
).
In interface 1, Make sure this wireless interface status is
Active
, enter
the
Wireless interface IP
(
default is 192.168.1.1
) and
Wireless
interface Net Mask
(
default is 255.255.255.0
) that are suitable for
your wireless network.
In interface 2, Make sure this Ethernet interface status is
Active
, and
specify the
Ethernet
IP address
(
default is 192.168.2.1
) and
Ethernet
Net Mask
(
default is 255.255.255.0
) of the Ethernet interface.
Click the
OK
button to return to the
Interface Parameter
window.
Finally, you need to click
FINISH
at the bottom of this page to complete
the modification of this page.
Hint1: Make sure interface 3 and 4 within status:
Disable
.
Hint2: In order to enable NAT service, choice the
NAT (PAT)
in the
interface Wireless and Ethernet. For example, make sure
Ethernet interface within
NAT (PAT)
On
and Wireless
interface is
NAT (PAT)
Off,
it means that every
communication through the Ethernet interface needs to do
NAT transfer.
4. Click
Basic Config
, and then select
System
as shown in
Figure 3-9
.
In the
System Setup
page, specify the
Default Route
(
Default is
192.168.2.254
) as the IP Address of the ADSL/Cable modem
connected to the AP or the IP Address of the Gateway in your LAN
environment, and Specify at least one IP address of the
DNS
parameter
(
Default DNS server 1 is 192.168.2.254
) provided by your
Summary of Contents for ALL0199AP
Page 26: ...48 Weight 2100 g 49 ...
