background image

TYLC4v1.0.0 

User manual

1.

Product Overview

        TYLC4  is  a  low-power  embedded  Wi-Fi  module  developed  by  Hangzhou  Tuya  Information 
Technology  Co.,  Ltd.,  which  consists  of  a  highly  integrated  RF  chip  ESP8266  and  a  few 
peripheral components with built-in Wi-Fi network protocol stack and abundant library functions. 
TYLC4  is  embedded  with  low  power  32-bit  CPU,  1  Mbyte  flash  memory  and  rich  peripheral 
resources.

 

TYLC4  is  a  RTOS  platform  which  integrates  all  the  function  libraries  of  Wi-Fi  MAC  and 

TCP/IP protocol, base on which, users are enabled to develop embedded Wi-Fi products according 
to their specific requirements.

 

1.1 Features

 

The embedded low-power 32-bit CPU can also be used as application processor

 

CPU Clock Speed: 80MHz and 160MHz

 

Working voltage: 3.0V-3.6V

 

Peripheral: 5×GPIOs, 1×UART

 

Wi-Fi connectivity

802.11 b/g/n

Channels 1-1

1

@2.4GHz

In support of WPA/WPA2 safe mode

In support of STA/AP/STA+AP operating mode

In  support  of  two  distribution  networks  including  SmartConfig  and  AP(Android  and

IOS devices included)

 

Operating temperature: -20

  to 125

1.2 Main applications

 

 

Intelligent building

 

Smart home/home appliances

 

Smart power plug, intelligent light

 

Industrial wireless control

 

Baby monitors

 

Webcams

 

Intelligent public transportation

Summary of Contents for TYLC4














Reviews: