Allnet ALL-SG8308PM User Manual Download Page 9 | Manualshive

Page: 9 / 39

background image

ALL-SG8308PM - User Manual

ALLNET GmbH Computersysteme 2015 – All rights reserved

9

Rear Panel

The 3-pronged power plug is placed at the rear panel of the switch right

side shown as below.

Hardware Installation

Set the switch on a large flat space with a power socket close by. The flat

space should be clean, smooth, level and sturdy. Make sure there is

enough clearance around the switch to allow attachment of cables, power

cord and allow air circulation. The last, use twisted pair cable to connect

this switch to your PC then user could start to operate the switch.

UL Warning

"The equipment is designed for building installation and not intended to

be connected to exposed (outside plant) networks including campus

environment and the ITE is to be connected only to PoE networks without

routing to the outside plant."

«
...
7
8
9
10
11
...
»

Summary of Contents for ALL-SG8308PM








































Reviews:

No comments

Related manuals for ALL-SG8308PM

Brand: Hama Pages: 14

Super Speed USB 3.0 Hub

Brand: Hama Pages: 14

Brand: Hama Pages: 12

Brand: Hama Pages: 14

Premium Silver USB 2.0 Hub 1:4

Brand: Hama Pages: 12

Brand: Hama Pages: 18

uRage Vendetta 210

Brand: Hama Pages: 36

Brand: SMART-AVI Pages: 2

Brand: Vega Pages: 28

Brand: Aastra Pages: 52

Brand: I-Tech Pages: 39

PMV WM Ultraswitch

Brand: Flowserve Pages: 16

Brand: Accton Technology Pages: 547

Brand: Radial Engineering Pages: 8

Brand: S&S Northern Pages: 8

Brand: Articona Pages: 2

Brand: JetNet Pages: 20

Brand: nedis Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands