Allied 96G2UH045BV12 Installation Instructions Manual Download

Page: 33 / 58

507961-01

Page 33 of 58

Issue 2128

Exhaust through Crawl Space Vent Option

All 33” condensing gas furnaces (92%+) are now approved

to be vented down through a crawl space. Ensure a vent

pipe drain kit, 51W18 (USA) or 15Z70 (Canada), is used as

directed through the floor joists and into the crawl space.

See the following figures.

Consult the vent tables for vent lengths and approved

materials.

2” or 3”

Sanitary Tee

1/2” PVC

Drain Stub

Drain Trap

Assembly

Rubber Boot (51W18)

Drain Plug (15Z70)

Clamp

(51W18 Only)

From

Furnace

To Vent

Termination

Drain Trap

(assembled)

Figure 49.

Kit 51W18 (USA) / 15Z70 (Canada) Parts

Identification and Assembly

Exhaust from

Furnace

To Termination

Exhaust from

Furnace

To Termination

* Kit 51W18 is shown.

Figure 50. Crawl Space Vent Pipe Drain Trap

Assembled Incorrectly

Figure 51.

Upflow or Downflow Furnace with Exhaust through Crawl Space

KIT 51W18 (USA)

Basement Floor

To Termination

1/2” PVC to

Code-Approved

Drain

24” max.

Downflow Furnace

Exhaust

KIT 15Z70 (Canada)

* Kit 51W18 is shown.

NOTE:

Upflow furnaces exhaust from the left side. All dimensions shown are typical for upflow or downflow furnaces.

NOTE:

All horizontal runs of exhaust pipe must slope back toward the kit a minimum of 1/4” (6mm) for each 12” (305mm) to ensure drainage.

Summary of Contents for 96G2UH045BV12



























































Search results

Summary of Contents for 96G2UH045BV12

Reviews:

Related manuals for 96G2UH045BV12

Brands by name

Popular brands

Allied 96G2UH045BV12, Installation Instructions Manual

Search results

Summary of Contents for 96G2UH045BV12

Reviews:

Related manuals for 96G2UH045BV12

Brands by name

Popular brands