Allied 96G2UH045BV12 Installation Instructions Manual Download

Page: 12 / 58

507961-01

Page 12 of 58

Issue 2128

Figure 15. Side Return Air

(with transition and filter)

Removing the Bottom Panel

Remove the two screws that secure the bottom cap to the

furnace. Pivot the bottom cap down to release the bottom

panel. Once the bottom panel has been removed, reinstall

the bottom cap. See Figure 16.

Figure 16. Removing the Bottom Panel

Horizontal Applications

Do not install the furnace on its front or its back. See

Figure 17.

WARNING

Figure 17.

This furnace can be installed in horizontal applications with

either right or left hand air discharge.

Refer to Figure 18 for clearances in horizontal applications.

Figure 18. Horizontal Application

Installation Clearances

Top

Bottom (floor)**

Air

Flow

Air

Flow

Right-Hand Discharge

Left-Hand Discharge

Bottom (floor)**

Top

Right End

Left End

Air

Flow

Air

Flow

Right End

Left End

Top

*Front

Back

Ends

Vent

Floor

0‡

* Front clearance in alcove installation must be 24 in. (610

mm). Maintain a minimum of 24 in. (610 mm) for front service

access.
** An 8” service clearance must be maintained below the unit

to provide for servicing of the condensate trap unless the trap

is mounted remotely.
‡ For installations on a combustible floor, do not install

the furnace directly on carpeting, tile or other combustible

materials other than wood flooring.

Summary of Contents for 96G2UH045BV12



























































Search results

Summary of Contents for 96G2UH045BV12

Reviews:

Related manuals for 96G2UH045BV12

Brands by name

Popular brands

Allied 96G2UH045BV12, Installation Instructions Manual

Search results

Summary of Contents for 96G2UH045BV12

Reviews:

Related manuals for 96G2UH045BV12

Brands by name

Popular brands