Allied 96G1DFE Installation Instructions Manual Download

Page: 4 / 53

507769-04

Page 4 of 53

Issue 1927

Gas Furnace

This Category IV gas furnace is shipped ready for

installation in the downflow position.

The furnace is equipped for installation in natural gas

applications. A conversion kit (ordered separately) is

required for use in propane/LP gas applications.

This unit can be installed as either a Direct Vent or a Non-

Direct Vent gas central furnace

NOTE:

In Direct Vent installations, combustion air is taken

from outdoors and flue gases are discharged outdoors. In

Non-Direct Vent installations, combustion air is taken from

indoors or ventilated attic or crawlspace and flue gases

are discharged outdoors. See Figure 2 for applications

involving roof termination.

Figure 2.

Shipping and Packing List

1 - Assembled Gas Unit

1 - Bag assembly containing the following:

1 - Snap bushing

1 - Snap Plug
1 - Wire tie
1 - Condensate trap
1 - Condensate trap cap
1 - Condensate trap clamp
1 - 2” diameter debris screen

1 - 3/4” Threaded street elbow

NOTE:

The required bellows grommet is field-provided.

See the Gas Piping section for relevant diagrams.

Check equipment for shipping damage. If you find any

damage, immediately contact the last carrier.

Please refer to specification sheets for available

accessories.

Safety Information

DANGER OF EXPLOSION!

There are circumstances in which odorant used with

LP/Propane gas can lose its scent. In case of a leak,

LP/Propane gas will settle close to the floor and may be

difficult to smell. An LP/Propane leak detector should be

installed in all LP applications.

DANGER

Use only the type of gas approved for use with this furnace.

Refer to unit nameplate.

This unit is CSA International certified to ANSI Z21.47 and

CSA 2.3 standards.

Building Codes

In the USA, installation of gas furnaces must conform with

local building codes. In the absence of local codes, units

must be installed according to the current National Fuel

Gas Code (ANSI Z223.1/NFPA 54). The National Fuel Gas

Code is available from the American National Standards

Institute, Inc., 11 West 42nd Street, New York, NY 10036.

In Canada, installation must conform with current National

Standard of Canada CSA-B149 Natural Gas and Propane

Installation Codes, local plumbing or waste water codes

and other applicable local codes.

Summary of Contents for 96G1DFE






















































Search results

Summary of Contents for 96G1DFE

Reviews:

Related manuals for 96G1DFE

Brands by name

Popular brands

Allied 96G1DFE, Installation Instructions Manual

Search results

Summary of Contents for 96G1DFE

Reviews:

Related manuals for 96G1DFE

Brands by name

Popular brands