background image

8

Patch Release Note

Patch 86222-10 for Software Release 2.2.2

C613-10319-00 REV J

A39 copper uplink modules in the Rapier G6 sometimes experienced 
spurious link up or link down events. This issue has been resolved.

The enterprise MIB now supports objects for power supply monitoring.

Certificates containing 

GeneralisedTime

 with the year in YYYY format are 

now parsed correctly. The 

keyUsage

 field of certificates is now parsed 

correctly when only one byte has been specified. The 

CRL update time

 is now 

displayed correctly in hours. If the 

username

 and 

password

 parameters are 

present the 

location

 parameter must be present and appear before the 

username

 and 

password

 parameters. Certificates with signatures of 257 bytes 

are now correctly parsed. Certificates added from a configuration script are 
now processed correctly.

A fatal error occurred if an IPv6 interface was deleted while packets were 
being transmitted. The number of current interfaces was not being updated 
correctly when a new IPv6 interface was added. As a result, after multiple 
additions and deletions, no more IPv6 interfaces could be added. These 
issues have been resolved.

The CREATE CONFIG command now adds PKI certificates to the script in 
the same order that they were originally added to the certificate database.

PKI certificates are now periodically checked (once per hour) to verify that 
they are still valid.

IPCOMP SA’s which have the reserved CPI “3” are no longer deleted by 
ISAKMP delete messages.

When a VLAN was created and then destroyed on the G6 or G6F, the 
VTABLE was corrupted. This has been fixed.

DHCP failed to send request messages when it was in a rebinding or 
renewing state. This issue has been resolved.

In some extreme traffic conditions the switch could lock up, preventing 
switching of any traffic. This issue has been resolved.

PCR: 01148

Module: SWI

Network affecting: No

PCR: 01157

Module: CORE

Network affecting: No

PCR: 01162

Module: PKI

Network affecting: No

PCR: 01170

Module: IPv6

Network affecting: No

PCR: 01176

Module: PKI

Network affecting: No

PCR: 01177

Module: PKI

Network affecting: No

PCR: 01178

Module: IPSEC

Network affecting: No

PCR: 01179

Module: SWI

Network affecting: No

PCR: 01181

Module: DHCP

Network affecting: No

PCR: 01185

Module: SWI

Network affecting: No

Summary of Contents for 86222-10















Reviews: