background image

Patch 86222-10 For Rapier Switches and AR800 Series Modular Switching Routers

3

Patch 86222-10 for Software Release 2.2.2
C613-10319-00 REV J

A configuration problem prevented trunking of gigabit ports at 100Mbit 
speeds. This issue has been resolved. The A39 gigabit copper uplink 
reverted to autonegotiation after a restart, even if it was configured to a 
fixed speed. This issue has been resolved. When the port has been 
configured for a fixed speed, the mode is now set to MDIX, not MDI.

When an M2 version of the AR020 PRI E1/T1 PIC was installed in a AR040 
NSM it was not possible to select the T1 mode of operation regardless of the 
jumper setting. This issue has been resolved.

A fatal error occurred when the firewall discarded disallowed multicast 
packets. This issue has been resolved.

Features in 86222-08

Patch file details for Patch 86222-08 are listed in Table 3.

Patch 86222-08 includes all issues resolved and enhancements released in 
previous patches for Software Release 2.2.2, and the following enhancements:

Tunnel creation failed when attempting to establish a point-to-point tunnel 
from an ATR router (tunnel originator) to another vendor’s router. This 
issue has been resolved.

When IGMP snooping was enabled, if a member left a group on a port, it 
could not re-join the group on that port. This issue has been resolved.

Substantial changes have been made to PIM in more recent code releases.  
These have been retrofitted to 2-2-2 in the patch. Note: these changes have 
incorporated PCRs 01159 and 01190.

The PPPoE access concentrator did not stop RADIUS accounting when a 
PADT termination was received without receiving a proper PPP 
termination first. This issue has been resolved.

PCR: 01248

Module: SWI

Network affecting: No

PCR: 01254

Module: PRI

Network affecting: No

PCR: 01256

Module: Firewall

Network affecting: No

Table 3: Patch file details for Patch 86222-08.

Base Software Release File

86s-222.rez

Patch Release Date

09-Nov-2001

Compressed Patch File Name

86222-08.paz

Compressed Patch File Size

291012 bytes

PCR: 01201

Module: L2TP

Network affecting: Yes

PCR: 01233

Module: PIM

Network affecting: No

PCR: 01236

Module: PPP

Network affecting: No

Summary of Contents for 86222-10















Reviews: