ALLIED DRONES AR25 Manual Download Page 4 | Manualshive

Page: 4 / 24

background image

rev 1 7/2016

4

Firmware

External Resources

Cleanflight Firmware & Configurator Software

 

http://cleanflight.com/

Betaflight Flight Control Firmware (installed in the AR25)

 

https://github.com/betaflight/betaflight

Betaflight Configurator

 

https://github.com/betaflight/betaflight-configurator

MW OSD Firmware & Configuration Software

 

http://www.mwosd.com/

BL Heli ESC Firmware & Configuration Software

 

https://blhelisuite.wordpress.com/

SiLabs Drivers for Flight Controller & ESCs

 

http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx

While drone racing is fast and exciting, this new
sport is not without its challenges. The only thing
faster than a racing drone are the advancements and
improvements to the software and firmware!

That being said, the AR25 comes fully configured
and tuned out of the box and should fly just fine for
most users. But for those looking to try to get the
most out of their hardware, these following resources
are worth exploring and studying in depth.

So to stay on top of the latest developments, keep
an eye on these sites listed here as well as
allieddrones.com for tutorials, support, and more.

«
...
2
3
4
5
6
...
»

Summary of Contents for AR25

























Reviews:

No comments

Related manuals for AR25

Brand: Parrot Pages: 4

Brand: Parrot Pages: 21

Brand: Radio Shack Pages: 2

Brand: Hobbico Pages: 15

ANAKIN NATURAL BORN RACER

Brand: SKY-HERO Pages: 19

Prism COAXIAL X8

Brand: WATTS INNOVATIONS Pages: 17

Brand: ProFlight Pages: 18

Brand: ProFlight Pages: 21

Smart Nano Drone

Brand: ONAGO FLY Pages: 6

Brand: Foxtech Pages: 12

Brand: Foxtech Pages: 16

GAIA 160HY-Hybrid A3 PRO

Brand: Foxtech Pages: 19

Brand: Foxtech Pages: 22

Brand: Foxtech Pages: 25

Brand: Foxtech Pages: 29

Brand: Foxtech Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands