ALLIANCE SCA030FN Original Instructions Manual Download Page 22

Page: 22 / 157

Troubleshooting

WARNING

To reduce the risk of electrical shock, fire, explosion,
serious injury or death:
• Disconnect electrical power to the washer-extrac-

tor before servicing it.

• Close the gas shut-off valve to the washer-extrac-

tor (when applicable) before servicing it.

• Never start the washer-extractor with any guards/

panels removed.

• Whenever ground wires are removed during serv-

icing, these ground wires must be reconnected to
ensure that the washer-extractor is properly
grounded.

W461R1

NOTE: To speed the process of troubleshooting, refer
to the Diagnostic section of the Programming Manual
for preliminary testing.

NOTE: Refer to the wiring diagram supplied with your
machine.

Troubleshooting

DO NOT COPY or TRANSMIT

Part No. F8677701EN

Summary of Contents for SCA030FN






























































































































































Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands

ALLIANCE SCA030FN, Original Instructions Manual

Search results

Summary of Contents for SCA030FN

Reviews:

Related manuals for SCA030FN

Brands by name

Popular brands