ALLIANCE Metered Installation & Operation Manual Download Page 54

Page: 54 / 54

Installer Checklist

Fast Track for Installing the Stacked Washer and Dryer

(Refer to the manual for more detailed information)

• Position Unit Near Area

of Installation.

CHECK

• Connect Fill Hoses.

CHECK

TLW1976N

HOT

COLD

TLW1976N

• Connect Drain Hose to

Drain Receptacle.

CHECK

SWD631N

Non-Gravity Drain Models Only

• Connect Drain Outlet to

Drain System.

CHECK

SWD745N

Gravity Drain Models Only

• Connect Gas Supply

Pipe.

• Check for Gas Leaks.

Gas Dryer Only

CHECK

D434I

• Connect Electrical Plug.

Electric Dryer Only

CHECK

D679IE0A

• Connect Dryer

Exhaust System.

CHECK

H312I

• Position and Level the

Unit.

CHECK

SWD796N

• Remove the Shock Sleeves

and Shipping Brace.

Washer Only

H336I

CHECK

• Wipe Out Inside of

Washer Drum and
Dryer Drum.

H315I

SWD797N

H315I

GAS DRYERS

AND WASHERS

CHECK

D254I

• Plug In Washer

and Dryer.

ELECTRIC

DRYERS

D275IE0E

D254I

CHECK

• Recheck Steps 1-11.

CHECK

• Check Heat Source.

Summary of Contents for Metered























































Search results

Summary of Contents for Metered

Reviews:

Related manuals for Metered

Brands by name

Popular brands

ALLIANCE Metered, Installation & Operation Manual

Search results

Summary of Contents for Metered

Reviews:

Related manuals for Metered

Brands by name

Popular brands