background image

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

Installation

17

802702

Connecting Power Cord with Three-Wire Plug

NOTE: Four-wire cord is required for mobile 
homes or where codes do not permit grounding 
through neutral.

Figure 10 

1. Disconnect power to dryer.

2. Remove access cover from rear of dryer.

Figure 11 

3. Use a strain relief and insert end of power cord 

through power supply hole.

Figure 12 

D816I

1

3 Wire Grounded Neutral 120/240 Volt, 60 Hertz 
AC 1 Phase Service Entrance Switch Box
(Refer to NOTE above)

4

Metallic or Non-Metallic Sheathed Cable 
(

Copper Wire Only

)

5

Power Cord (Not supplied with dryer)

2

30 Ampere Fuses or Circuit Breaker

6

Neutral

3

Neutral Wire

7

Terminal Block in Dryer

NOTE: The power cord is NOT supplied with the 
electric dryer. Type of power cord and gauge of wire 
must conform to local codes and instructions.

The method of wiring the dryer is optional and subject 
to local code requirements.

NOTE: Connect the dryer to the power supply with the 
MAXIMUM RATED VOLTAGE listed on the nameplate.

1

3

5

6

7

4

2

POWER CORD CONNECTION

DIRECT CONNECTION

L1

L2

L1

L2

INTERMEDIATE 
SHUT-OFF BOX 

(may or may not 

be fused)

POWER SUPPLY

POWER SUPPLY

INTERMEDIATE 

FUSE BOX (may 

be omitted if 

service entrance 

box is fused)

WALL 

RECEPTACLE

A typical 

30-Amp 

Three-Wire 
Receptacle 

NEMA Type 

10-30R

120 ± 12

V.A.C.

120 ± 12

V.A.C.

240 ± 12

V.A.C.

NOTE: Use COPPER WIRE only. 
Shorter than 15 ft. (4.5 m) – use 10 AWG
Longer than 15 ft. (4.5 m) – use 8 AWG

D695I

D696I

Summary of Contents for Metered























































Reviews: