Alliance Laundry Systems AT0350SRG Service Manual Download Page 33

Page: 33 / 60

70143101

Section 5 Service Procedures

To reduce the risk of electric shock, fire, explosion, serious injury or death:

• Disconnect electric power to the tumbler before servicing.

• Close gas shut-off valve to gas tumbler before servicing.

• Close steam valve to steam tumbler before servicing.

• Never start the tumbler with any guards/panels removed.

• Whenever ground wires are removed during servicing, these ground wires must be

reconnected to ensure that the tumbler is properly grounded.

W002

WARNING

30. ROLLER SUPPORT AND BAFFLE

ASSEMBLY

Refer to

Figure 21

a. Remove cylinder and bearing assembly. Refer

Paragraph 27

b. Remove cylinder seals. Refer to

Paragraph 29

c. Remove screws holding roller support to

cabinet.

d. Remove screws holding baffles to heat shields.

e. Remove screws holding baffles to center

partition.

f. Remove baffles.

Figure 21

T410PE3B

BAFFLE

GASKET

ROLLER

SUPPORT

CENTER

PARTITION

HEAT SHIELDS

BAFFLE

Summary of Contents for AT0350SRG





























































Search results

Summary of Contents for AT0350SRG

Reviews:

Related manuals for AT0350SRG

Brands by name

Popular brands

Alliance Laundry Systems AT0350SRG, Service Manual

Search results

Summary of Contents for AT0350SRG

Reviews:

Related manuals for AT0350SRG

Brands by name

Popular brands