background image

1-8

SECTION 1

SAFETY

056335; 01/12

1.4
Engine Safety

1.4.1

Engine Safety

Internal combustion engines present special hazards during operation
and fueling. Read and follow the warning instructions in the engine
owner’s manual and the safety guidelines below. Failure to follow the
warnings and safety guidelines could result in severe injury or death.

1.4.2

DO NOT

run the machine indoors or in an enclosed area such as a deep trench

unless adequate ventilation, through such items as exhaust fans or hoses, is
provided. Exhaust gas from the engine contains poisonous carbon monoxide gas;
exposure to carbon monoxide can cause loss of consciousness and may lead to
death.

1.4.3

DO NOT 

smoke while operating the machine.

1.4.4

DO NOT

smoke when refueling the engine.

1.4.5

DO NOT

refuel a hot or running engine.

1.4.6

DO NOT

refuel the engine near an open flame.

1.4.7

DO NOT

spill fuel when refueling the engine.

1.4.8

DO NOT

run the engine near open flames.

1.4.9

ALWAYS

refill the fuel tank in a well-ventilated area.

1.4.10

ALWAYS

replace the fuel tank cap after refueling.

1.4.11

ALWAYS

keep the area around the muffler free of debris such as leaves, paper,

cartons, etc. A hot muffler could ignite the debris and start a fire.

Summary of Contents for HDX750



















































































Reviews: