background image

INSTRUCTIONAL

OWNER’S MANUAL

7

OPEN FRAME

Remove trailer and all components from carton. Unfold trailer 
by pulling the frame and remove all components from inside.  
Note that the window tubes are made in two pieces, and are 
connected by a spring pin located in the rear half of the win-
dow frame tubes. To assemble, slide the fabric sleeve forward 
to access the end of the frame tube. Next, slide the back half 
of the tube into the end of the frame tube (Fig 2), and allow 
the spring pin to lock in place. (Fig 2a) 

Once the window tubes are assembled, lift the rear frame tube and align with the U-bracket at the rear of the win-
dow tube. (Fig 3).  Slide the U-bracket over the rear frame tube, aligning the holes in the bracket and tube. (Fig 3a) 
Slide the QR pin through the holes in the tube, (Fig 4), and loop then end over the shaft of the pin to lock it in place. 
(Fig 5a).  Frame is now assembled (Fig 5a).

MAIN CABIN FRAME AND ASSEMBLY

STEP 1:

STEP 2:

Remove the trailer, wheels, hitch arm and walking kit from the box.

FIGURE 2.

FIGURE 4.

FIGURE 3.

FIGURE 5.

FIGURE 2A.

FIGURE 4A.

FIGURE 3A.

FIGURE 5A.

WARNING:

  

 

Immediately discard all plastic bags and plastic wrapping  

 materials!

FIGURE 1

NOTE:

  

  IFrame must be properly assembled with quick release pins close and snapped shut. If QR pins are not correctly  

 

 

attached, frame may collapse, causing damage or injury. Do not use if QR pins are missing, or if the closure is  

 

 

damaged or missing.

NOTE:

  

  This process only needed for initial assembly. When folding for transport or storage, it is not necessary to 

 

 

disassemble the side frame tubes.

WARNING:

  

 

The spring-release pins must be engaged for safe operation of the trailer. Failure to assemble properly  

 

may result in frame collapse, resulting in damage to the trailer and injury to the user. If the spring-re   

 

lease pins do not engage properly, DO NOT USE. Call the customer service number as indicated in the   

 

attached literature for assembly assistance.

Summary of Contents for T2 BIKE TRAILER













Reviews: