manualshive.com logo in svg

Allen-Bradley ProcessLogix 1757-PLX52, Installation Instructions Manual, Page: 16 / 24

Share
Download
Allen-Bradley ProcessLogix 1757-PLX52 Installation Instructions Manual Download Page 16

16

ProcessLogix Hardware

Publication 1757-5.1 - August 1999

Verify the Ethernet Adapter and TCP/IP Address

The ProcessLogix server uses Ethernet hardware and the TCP/IP protocol to 
communicate with client user stations. Even if your system does not have a client 
user station, you will need to install an adapter and configure a TCP/IP address for 
proper communication.

Verify the Ethernet adapter

1.

In your Microsoft Windows NT

 

desktop, select Start

⇒

Settings

⇒

Control 

Panel.

2.

Double-click on the Network icon. You see the Network screen.

3.

Click the Adapters tab. You see the Network Adapters screen.

IMPORTANT

If your server and remote stations do not have Ethernet cards 
installed, you can use the Microsoft loopback adapter provided 
with the NT operating system. The loopback adapter is a 
software program that emulates the operation of the Ethernet 
card

TIP

On this screen, adapter (1) is an Ethernet card. Adapter (2) is the 
loopback adapter. Your configuration may vary.

Summary of Contents for ProcessLogix 1757-PLX52

























Reviews:

No comments