Allen-Bradley 5069-IA16 User Manual Download

Page: 113 / 296

Rockwell Automation Publication 5069-UM004A-EN-P - April 2019

113

Output Module Features

Chapter 4

No Load Detection

No Load Detection detects when a wire is disconnected from the output or a
missing load for each output point in the Off state.

• No Load Detection is disabled by default on Compact 5000 I/O

standard output modules.

You must enable the feature in your Logix Designer application project.

• No Load Detection is enabled by default on Compact 5000 I/O safety

output modules. You cannot configure it.

The output modules support the following minimum load currents:

• Standard output modules:

– No load detection current, max = 0.5 mA
– On-state current per channel, max = 1 mA

• Safety output modules - The load detection current is ≥10 mA. For

example, 2.4 Ω at 24V DC.

In the On state, the module must be connected to a load that draws a minimum
current equal to the following values.

Table 26

describes what happens when a No Load

condition is detected

5069-OBV8S

SIL2 CPU

5069-L3100ERMS2

Compact GuardLogix

5069-OBV8S

5069-IB8S

OUTPUT

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

SA P

MOD P

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

Standard Modules

Safety Modules

™

NET B1

LINK B1

NET A1

LINK A1

NET A2

LINK A2

SPEED X1

LINK X1

RUN

FORCE

FAN 1

FAN 2

Compact

Logix

5480

5069-L46ERMW

CONTROLLER

UPS

R
B
F

DC INPUT

5069-IB16

DC OUTPUT

5069-OB16

ANALOG INPUT

5069-IY4

ANALOG OUTPUT

5069-OF8

DC INPUT

5069-IB16

IMPORTANT

The following Compact 5000 I/O digital output modules support No Load
Detection:

• 5069-OB8

• 5069-OB16

• 5069-OB16F

• 5069-OB16K

• 5069-OBV8S

• 5069-OBV8SK

IMPORTANT

An output must remain in the off state a minimum of 250 ms for an open
load to be detected.

Table 26 - No Load Detection - Compact 5000 I/O Digital Output Modules

Tag Value

I/O Status Indicator State

I.Ptxx.NoLoad tag = 1

• Compact 5000 I/O standard output modules - Flashing red if the No Load

condition exists

• Compact 5000 I/O safety output modules -

– Flashing red if a No Load condition exists and the output is off.
– Flashing red/yellow if a No Load condition already exists and the

output is on.

IMPORTANT

: A No Load condition is only detected when the output is off.

Summary of Contents for 5069-IA16









































































































































































































































































































Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands

Allen-Bradley 5069-IA16, User Manual

Search results

Summary of Contents for 5069-IA16

Reviews:

Related manuals for 5069-IA16

Brands by name

Popular brands