Allen-Bradley 2711P-RAAK10 Installation Instructions Manual Download Page 2

2

Rockwell Automation Publication VIEW-IN002C-EN-P - October 2018

Adapter Kit for PanelView 5000 and PanelView Plus 7 Performance Terminals

About This Adapter Kit

This adapter kit includes an adapter plate, gasket, and backing plate that you install into an 
existing cutout from a PanelView™ Plus 6 or PanelView standard terminal. Read and understand 
these instructions before you begin to install the adapter plate kit and terminal.

See th

Adapter Kit Conversion Table on page 2

 to determine the adapter kit for your new and 

existing terminal.

Adapter Kit Conversion Table

IMPORTANT

Do not install a PanelView Plus 7 Standard terminal with this adapter kit. This adapter kit is 
only for PanelView 5000 and PanelView Plus 7 Performance terminals.

If you install a PanelView Plus 7 Standard terminal into this adapter kit, you can damage the 
standard terminal bezel. Contaminates can also enter the enclosure and damage components 
inside the enclosure.

Adapter Kit 

Cat. No.

Replace this Existing PanelView Plus 6 or 

PanelView Standard Terminal…

With this PanelView 

5000 or PanelView 

Plus 7 Performance 

Terminal

Uses Drill 

Template 

Cat. No.

2711P-RAAT7

PanelView Plus 6 700 touch screen

6.5-in. touch screen

VIEW-DS002

2711P-RAAK7

• PanelView Plus 6 700 keypad, or keypad with touch screen
• PanelView Standard 600 keypad, or keypad with touch 

screen

6.5-in. keypad 
with touch screen

2711P-RAAT10

• PanelView Plus 6 1000 touch screen
• PanelView Standard 900 touch screen

10.4-in. touch screen

VIEW-DS003

2711P-RAAK10

• PanelView Plus 6 1000 keypad, or keypad with touch screen
• PanelView Standard 900 keypad

10.4-in. keypad 
with touch screen

2711P-RAAT12

• PanelView Plus 6 1250 touch screen
• PanelView Standard 1000 touch screen

12.1-in. touch screen

VIEW-DS004

2711P-RAAT12K

• PanelView Plus 6 1250 keypad, or keypad with touch screen
• PanelView Standard 1000 keypad

12.1-in. touch screen

2711P-RAAT15

• PanelView Plus 6 1500 touch screen
• PanelView Standard 1400 touch screen

15-in. touch screen

VIEW-DS005

2711P-RAAK15

• PanelView Plus 6 1500 keypad, or keypad with touch screen
• PanelView Standard 1400 keypad

15-in. keypad 
with touch screen

Summary of Contents for 2711P-RAAK10

















Reviews: