ALLEN & HEATH XONE:DB2 User Manual Download Page 37

Page: 37 / 41

Allen & Heath

XONE:DB2 User Guide

AP8640_2

DIGITAL IO - X-LINK

DIGITAL INPUTS - DIGITAL OUTPUT

DIGITAL INPUTS 1&2

DIGITAL INPUT:

The XONE:DB2 has two digital inputs on the rear panel designed for standard 75

Ohm RCA interface cables. These inputs are compatible with the following formats:
AES3, IEC60958, S/PDIF (Sony/Phillips Digital Interconnect Format), EIAJ CP1201, all from 32kHz to
192kHz, and up to 24bits.

DIGITAL OUTPUT:

The digital output is fixed at 48kHz/24 bit, non copy protected, with a 75 Ohm

impedance.
The digital output source, and signal level is set in the Menu under “Record Setup”, see page 23 for
details.

DIGITAL OUTPUT

X-LINK

X-Link

is a proprietary interface protocol to enable future Allen & Heath accessories and controllers to

be easily connected to the XONE:DB2. Visit www.XONE.co.uk for the latest news on X-Link enabled
products.

Dual FX Core DSP engine: 2 simultaneous FX engines with independent BPM calculation.

Analogue/Digital conversion

24 bit

Analogue/Digital Line-up

+12dBu = 0dBFS

DSP processing

24 bit I/O + 48 bit EQ

DSP Mix Bus

56 bit Fixed Point

DSP core sampling frequency

48kHz

USB soundcard sampling frequency

48kHz

SPDIF input sampling frequency range

32kHz to 192kHz

SPDIF Output sampling frequency

48kHz

DIGITAL ARCHITECTURE SPECIFICATION

Summary of Contents for XONE:DB2










































Search results

Summary of Contents for XONE:DB2

Reviews:

Related manuals for XONE:DB2

Brands by name

Popular brands

ALLEN & HEATH XONE:DB2, User Manual

Search results

Summary of Contents for XONE:DB2

Reviews:

Related manuals for XONE:DB2

Brands by name

Popular brands