ALLEN & HEATH XONE:4D User Manual Download Page 14

Page: 14 / 48

Allen & Heath

XONE:4D User Guide

SOUNDCARD SOFTWARE DESCRIPTION

SOFTWARE DESCRIPTION

The inputs and outputs of the soundcard have a description within the software being

used. Below are the descriptions used in Ableton and Traktor.

Soundcard Input

Ableton Descriptor

Traktor Descriptor

1-2

1/2 (Stereo)

IN 0-Allen&Heath Xone:4D

1 (Mono) & 2 (Mono)

IN 1-Allen&Heath Xone:4D

3-4

3/4 (Stereo)

IN 2-Allen&Heath Xone:4D

3 (Mono) & 4 (Mono)

IN 3-Allen&Heath Xone:4D

5-6

5/6 (Stereo)

IN 4-Allen&Heath Xone:4D

5 (Mono) & 6 (Mono)

IN 5-Allen&Heath Xone:4D

7-8

7/8 (Stereo)

IN 6-Allen&Heath Xone:4D

7 (Mono) & 8 (Mono)

IN 7-Allen&Heath Xone:4D

9-10 (Digital in 1-2)

9/10 (Stereo)

IN 8-Allen&Heath Xone:4D

9 (Mono) & 10(Mono)

IN 9-Allen&Heath Xone:4D

Soundcard Output

Ableton Descriptor

Traktor Descriptor

1-2

1/2 (Stereo)

OUT 0-Allen&Heath Xone:4D

1 (Mono) & 2 (Mono)

OUT 1-Allen&Heath Xone:4D

3-4

3/4 (Stereo)

OUT 2-Allen&Heath Xone:4D

3 (Mono) & 4 (Mono)

OUT 3-Allen&Heath Xone:4D

5-6

5/6 (Stereo)

OUT 4-Allen&Heath Xone:4D

5 (Mono) & 6 (Mono)

OUT 5-Allen&Heath Xone:4D

7-8

7/8 (Stereo)

OUT 6-Allen&Heath Xone:4D

7 (Mono) & 8 (Mono)

OUT 7-Allen&Heath Xone:4D

9-10 (Digital Out 3-4)

9/10 (Stereo)

OUT 8-Allen&Heath Xone:4D

9 (Mono) & 10 (Mono)

OUT 9-Allen&Heath Xone:4D

Supported Buffer Sizes

The Xone:4D supports the following buffer sizes:

64, 96, 128, 192, 256, 384, 512, 768, 1024 etc.

Summary of Contents for XONE:4D

















































Search results

Summary of Contents for XONE:4D

Reviews:

Related manuals for XONE:4D

Brands by name

Popular brands

ALLEN & HEATH XONE:4D, User Manual

Search results

Summary of Contents for XONE:4D

Reviews:

Related manuals for XONE:4D

Brands by name

Popular brands