manualshive.com logo in svg

Alinco DJ-V57, Instruction Manual

Share
Download
Alinco DJ-V57 Instruction Manual Download Page 46

8.Set Mode

8

46

8.3.1 Menu 1 Battery Save (BS) Function

This function prevents useless battery consumption by switching the power ON/OFF

at a fixed ratio if there is no key operation or receiving signal for a continuous period

of 5 seconds or more.

1. BS-1 is displayed on the LCD.

2. Rotate the dial to select BS-1, BS-2 or OFF.

BS-1 saves the more amount of battery but may cause slight delay on receiving. BS-2 allows

smoother communication but saves the less amount of battery. OFF cancels the BS function.

• The factory setting is BS-1.

• The Battery Save function is temporarily suspended when a key is operated or a

signal is received.

• Set this parameter OFF for packet operation.

• The display remain unchanged even the BS function is in the OFF cycle.

8.3.2 Menu 2 Timer/Busy Scan Setting

Select the scan-resume condition in this menu (page 33).

1. TIMER1 is displayed on the LCD.

2. Rotate the dial to select TIMER1, TIMER2 or BUSY.

8.3.3 Menu 3 Beep Function

Select OFF to turn off all the beep sounds inclusive of alerting beeps.

1. BEP-ON is displayed on the LCD.

2. Rotate the dial to select the beep setting on and off.

8.3.4 Menu 4 VOX delay time setting

When VOX is used, the transmitting is delayed. This function prevents the transmitting

of unexpected noise.

1. VOD-OF is displayed on the LCD.

2. Rotate the dial to select the VOX delay setting on and off.

VOD-OF

VOD-ON

BEP-ON

BEP-OF

TIMER1

TIMER2

BUSY

Stop time

•

 TIMER1 : 5s

•

 TIMER2 : 2.5s

BS-1

BS-2

BS-OFF

Available Parameters

8.3

Summary of Contents for DJ-V57









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands