Alinco DJ-A10 Instruction Manual Download Page 69

Page: 69 / 81

Professional
FM Transceiver

5ST:

When receives signal, scan stops for 5 seconds and resume.

10ST:

Same, 10 seconds.

15ST:

Same, 15 seconds and default is 10s.

Frequency/Channel Display Mode

There are 3 different display modes available, Fre Channel mode,

Channel mode and Name Tag modes.

1.Press and hold

【

PF2

】

key while turning on the radio, and keep pressing

【

PF2

】

key for 3 seconds to enter into the Set Mode operations.

2.Press【

】/【

】key to choose the Menu 12 and display “

DSP

”.

3.Press

【

】

key then press

【

】

key or

【

】

key to choose the parameter.

FREQ:

Fre Channel mode (VFO mode). Press

【

】

key to switch into

VFO mode.

CH:

Channel mode. Note that manual setting is not available when the radio has

been preprogrammed by the dealer using software.

NAME:

Name Tag mode(VFO mode). Press

【

】

key to switch into

VFO mode.
Default setting is FREQ.

Tone Burst Tone

Especially in Europe, Tone-burst tone operated repeaters are popular. To access to those repeaters,

SET MODE OPERATIONS

Summary of Contents for DJ-A10


















































































Search results

Summary of Contents for DJ-A10

Reviews:

Related manuals for DJ-A10

Brands by name

Popular brands

Alinco DJ-A10, Instruction Manual

Search results

Summary of Contents for DJ-A10

Reviews:

Related manuals for DJ-A10

Brands by name

Popular brands