1
www.observint.com
ALI-TS2128R_CQ
190708
What you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for requirements
•
Tools and additional fasteners (may be required) for mounting the camera
•
Phillips #2 screwdriver
•
Video and power extension cable
•
HD-TVI or CVBS video setup monitor (optional)
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
During installation:
•
Camera Lens
: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning
section.
•
Power supply
:
Camera drop cable
: The camera drop cable includes two connectors:
—
Video BNC connector
: For transmission of the video signal across a coax (75 Ω) extension
cable to an 8 MP compatible recorder.
—
Power connector:
When applying power, observe the power polarity. See the picture to the
left for the connector polarity configuration.
1.
Using the drill template provided with your camera, mark the location of the screws that anchor the
base plate to the mounting surface. If you are routing the drop cable through base, also mark the
position of the hole for the drop cable.
2.
Drill holes for the screws that anchor the base to the ceiling. The mounting hardware provided is
appropriate for most surfaces. However, depending on the surface materials, more appropriate
fasteners may be required.
3.
Drill a 3/4” hole for the drop cable, if necessary. The drop cable can be routed through the mounting
surface, or through a cable channel in the mounting plate.
4.
Route camera video and power extension cables between camera location and the monitoring
device (monitor, DVR, etc.).
5.
Remove the mounting plate from the camera assembly
u
Loosen the clip plate captive screw with the security L-wrench provided.
u
v
Clip plate
Enclosure
v
Slide the clip plate out as shown in the photo above.
Separate the mounting base from the enclosure.
ALI-TS2128R 8MP TVI/AHD/CVI/CVBS
Varifocal 200 ft IR Outdoor Turret Camera
Quick Installation Guide
The ALIBI ALI-TS2128R turret camera include a 4 -in-1 switchable video output (TVI/AHD/CVI/CVBS) with
an 8.29 MP sensor. This camera features:
•
8.29 Megapixel (3840 x 2160 pixels) high-performance CMOS sensor
•
Switchable video output for TVI, AHD, CVI, or CVBS
•
2.7 mm – 13.5 mm motorized varifocal lens with horizontal Field of View 108.1° to 45.6°
•
Low light 0.01 lux color illumination
•
EXIR 2.0, 200 ft Smart IR
•
OSD menu (up-the-coax OSD control),
•
105 dB Digital Wide Dynamic Range (DWDR)
•
IP67 Weather rated housing
Mounting
base
Enclosure
Cable
guide (2)
Clip plate
Orientation
mark (UP)
Lens
Turret
Photosensor
ALI-TS2128R camera
Switch*
button
Cap for
switch
button
12 Vdc power in
HD video BNC connector
* Press and hold button for 5 seconds to change the video format. See cable tag.
Camera drop cable connectors
What’s in the box
•
Camera assembly
•
Mounting hardware
•
Drill template
•
Security L-wrench for clip plate
•
This instruction guide
