5
www.observint.com
© 2014 Observint Technologies. All rights reserved..
5.
Open Internet Explorer and log into the camera again. The Live View - Main stream window will
appear.
Microphone, Capture, Record, icons
Focus, Zoom
controls
Screen select tabs
Live View options
Logout button
Live View image
Step 6. Adjust the camera for your surveillance target
1.
Observe the Live View screen to
adjust the direction of the camera.
To adjust the camera pan, grasp the
camera gimbal on both sides at the
pivot point, then rotate the as shown
in the left illustration below.
Camera gimbal
on sides here
To adjust the tilt, rock the gimbal as
shown above in the right illustration.
Grasp here
To adjust the horizontal alignment,
grasp the lens assembly at the top
and bottom, and then roll it left or
right as needed.
Grasp here
2.
Use the zoom and focus controls on the PTZ section of the Live View screen to make Zoom and Focus
adjustments, if necessary.
NOTE
: The camera features auto focus.
3.
Reattach the camera dome assembly.
Step 7. Setup the video image
The video Display Settings menu includes the image-related configurable parameters for the camera. It
contains several sub-menus such as Image Adjustment, Exposure Settings, Day/Night Switch, etc. that can
be opened or closed for compactness. Additionally, several adjustments can be seen in the Live View image
on the menu. To open the Display Settings menu, go to
Setup
tab
| Image | Display Settings
Configurable parameters include:
•
Switch Day and Night
: Select either
Auto-Switch
or
Scheduled-Switch
.
—
If using
Auto-Switch
, open the
Day/Night Switch
submenu to select the Sensitivity,
Filtering Time, and Smart IR feature ON or OFF.
—
If using
Scheduled Switch
, set the
Start Time
and
End Time
of the switch, then open
the
Day/Night Switch
submenu to select the
Smart IR
feature ON or OFF.
Also, click the
Common
,
Day
and
Night
tabs to set the Saturation, Hue, Brightness,
Contrast and Sharpness for Day and for Night modes.
•
Image Adjustment
submenu: Open the Image adjustment submenu to set the Saturation, Hue,
Brightness, Contrast and Sharpness of the video image. Each parameter can be set to a level of 0
~ 100 either by moving the slider or entering the value in the box on the right. The effect of the
adjustment will appear in the Live View image in the menu.
•
Exposure Settings
submenu: In this submenu, set the following for the best performance:
—
Iris Mode
: Select Auto or Manual. Some cameras may not offer both options.
—
Exposure Time
: Value ranges from 1/3 to 1/100,000 s. The nominal value is 1/150. Adjust it
according to the lightening condition.
—
Gain
: Set the gain to show the optimal brightness level.
•
Day/Night Switch
submenu: You can set the Day/Night switch to Day, Night, Auto, or Schedule.
The option you select determines the submenu options.
—
Day
or
Night
: These options both have one parameter: Smart IR.
—
Auto
: If you select Auto switch, you can set the sensitivity (0 .. 7), filtering time and Smart IR.
—
Schedule
: Use Schedule to set that
Start Time
and
End Time
for the switch. Smart IR is
also selectable.
•
Backlight Settings
: Backlight settings include BLC Area (Off, Up, Down Left Right Center), the
area to control, and
WDR
(Wide Dynamic Range) ON or OFF.
•
White Balance
: White Balance selection is used to correct colors in the image depending on the
lighting source. You can also set the white balance manually (MWB), using Automatic White Balance
(AWB1), and lock the white balance setting (Locked WB).
•
Image Enhancement
: Options in this submenu include Digital Noise Reduction (DNR) ON or OFF.
If ON, yo can also adjust the level of noise reduction.
•
Video Adjustment
: Video Adjustment includes:
