manualshive.com logo in svg

ALGE-Timing TELEDATA TED-RX, Manual, Page: 4 / 31

Share
Download
ALGE-Timing TELEDATA TED-RX Manual Download Page 4

TED-TX / RX

Page 4

1.   GENERAL

Use:

Wireless transmission of timing impulses and data

Radio Frequency:

70 cm band (standard frequency= 433,500 MHz)

TED-Types:

TED-TX10:

Teledata Transmitter with a RF output power of 10 mW,
about 1.5 km reach, built in l/4 antenna

TED-TX400:

Teledata Transmitter with a RF output power of 10 mW,
about 1.5 km reach, antenna connection through BNC

socket

TED-RX:

Teledata receiver (for TED-TX10 and TED-TX400
identical), built in l/4 antenna

Minimum configuration:

1 TED-TX and 1 TED-RX

Additions:

additional TED-TX for impulse- or data transmission
additional TED-RX for data transmission
RX-C10:

impulse transmission for two and more timing channels

Identification for TED-TX:

device sticker (15) and green holder (2)

Identification for TED-RX:

device sticker (15) and red holder (2)

Information on the device sticker:

- device type

- device frequency

- device number

- power output (only on TED-TX)

Impulse transmission:

The impulse transmission works direct from any ALGE impulse
device  to any ALGE timing device.

Data transmission ALGE 1 Sec.: The TED-TX sends each data string 10 times. It sends per

second one different data string.

Data transmission ALGE 0.1 Sec.:The TED-TX sends each data string 1 time. It sends per 0.1

second one data string.

Data transmission 2400 Baud:

Data transmission with 2400 Baud, where it needs a code at
the beginning and end of each data package.

Data transmission 4800 Baud:

Data transmission with 4800 Baud, where it needs a code at
the beginning and end of each data package.

Data transmission Direct:

Transmits all data, the transmitter is always turned on.

System test:

signal strength test
interference test

Power supply:

6 batteries (type AA) or
6 NiCd batteries (type AA)
external supply

Summary of Contents for TELEDATA TED-RX
































Reviews:

No comments