background image

 

LOCATING AND ASSEMBLING THE SIDE BURNER:

 

 
When determining a suitable location for your Side Burner, take into account concerns such as exposure 
to  wind,  rain,  sprinklers,  proximity  to  traffic  paths  and  keeping  any  gas  supply  line  runs  as  short  as 
possible. 
Locate the Side Burner only in a well-ventilated area. Never locate the Side Burner in a building, garage, 
breezeway,  shed  or  other  such  enclosed  areas  without  an  approved  ventilation  system.    Never  locate 
the Side Burner over, under or next to unprotected combustible construction.  
 

CLEARANCES:

 

 
TO NON-COMBUSTIBLE CONSTRUCTIONS: 
A minimum of 3”  clearance around the Side Burner to non-combustible construction is required to allow 
heat to escape freely while cooking. 
 
TO COMBUSTIBLE CONSTRUCTIONS: 
This appliance should NOT be located over, under or next to unprotected combustible construction.  
 
 

ASSEMBLY:

 

 
BUILT-IN MODELS: 
 
To locate your ALFRESCO™ Side Burner into your Non-combustible enclosure, complete the following 
steps: 
 

1.  Remove all packaging materials 
2.  Install and secure the body of the Side Burner to your counter’s enclosure. 
3.  Ensure  that  the  burners  are  positioned  correctly  on  their  venturi  funnels,  and  are  fully 

seated onto their supports. (See figure # 1) 

4.  Install the Side Burner Grate. 
5.  Make the connection to the gas regulator according to the instructions on pages 8 & 9 for 

your gas type. 

6.  To  comply  with  safety  and  service  requirements,  main  gas  shut  off  valve  must  be 

accessible from front of Side burner without using any tools. 

 

 
CART MODELS: 
 
Please follow the instructions supplied with the unit in order to mount and connect all required piping that 
comes with the unit. 
 

WARNING: 

 
To prevent harm and ensure proper operation of your Side Burner, it is imperative that the burners are 
properly installed with respect to the gas orifices. Be certain that the exterior cap and well as internal cap 
is inserted completely into the burner’s venture funnel and that the burner rests firmly on its supports. 
 
The  burner  should  not  rock  side-to-side  nor  top-to-bottom  if  properly  installed.  If  excessive  burner 
movement is present, reseat burner or contact your authorized service provider. 

Summary of Contents for ALSB-2





















Reviews: