background image

150 TURBO / 150 

Ultima modifica/ Last Update: 18/03/2008   Rev0                                                                                                                       pagina 9 di 15 

PROBLEM 

CASE 

SOLUTION 

The machine does not 
switch on. 

 

Electrical power does not reach the ma-
chine. 

 
 
 

 

Voltage reaches the machine switch but 
there is no voltage after the contacts.  

 
 

 

There is voltage after the disconnecting 
switch but the machine does not go on.  

!

Make sure the line switches are closed, the 
protection devices (fuses) have not been 
enabled and that the power supply cable is 
intact. 

!

Switch the machine off and disconnect the 
plug. Make sure that when the switch is 
closed, there is continuity between the 
contact input and output and that the varis-
tor is not broken (picture 4). If it’s dama-
ged, the Power Board must be replaced. 

!

Switch the machine off and disconnect the 
plug. Check the mosfet of the switching 
power supply unit on the power board 
(picture 5). 

The protection devices 
of the line set off when 
the switch is activated 
and the machine does 
not go on. 

 

Damaged power supply cable with short-
circuited wires.  

 
 

 

Inverter is damaged. 

!

Switch off the machine and disconnect the 
plug. Make sure that there are no short cir-
cuits between the poles of the plug caused 
by a damaged power supply cable.  

!

Switch  off  the  machine,  disconnect  the 
plug and check: 
-   varistors (picture 4); 
-   inverter (picture 3); 
-   Input bridge rectifier (picture 2);  

 

switching power supply unit (picture 5). 

If  one  of  these  components  is  damaged 
replace the power board. 

The front panel does 
not switch on. 

 

The fan works but the front panel does 
not go on. 

 
 
 
 
 
 

 

Both the fan and the front panel do not 
work. 

!

Switch off the machine and disconnect the 
plug. Make sure the flat cable that con-
nects the front panel to the power board is 
inserted correctly. If correctly inserted, re-
place the front panel. If the front panel 
does not go on, one of the switching power 
supply unit outputs is broken. Therefore 
the power board must be replaced. 

!

Switch off the machine, disconnect the 
plug and check the mosfet of the switching 
power supply unit (picture 5). 

 !"#$%&'(

)*+,-*( ./--0123( ,45( /20( 6,-7( ,2( 58*( 9/.812*(

9/7*( :4-*( 15( 1:( ,++( /2;( 58*( <=43( 8/:( >**2( ;1:?

.,22*.5*;@(

'(

Summary of Contents for 150 TP
















Reviews: