20
Once you have adjusted and confirmed the operation of the clock, the LED lamp 1 (left, up) on the keyboard will
switch on and will stay on. Temporarily recontrol the accuracy of the clock and if it is disrupted you can adjust it
once again according to the manner described above.
In order to come out of the program at any time, press once the button for switching off the stove (button 4)
in duration of not less than 2 seconds.
Automatic starting and switching off of the stove
If you want automatic starting and switching off of the stove, the clock must be adjusted as described.
Once you’ve adjusted the clock and reached the parameter
UT04
, press SET once again to go to
UT05
. Now here
you can select the time of starting for the program of the first automatic starting of the stove, again by using the
buttons 1 and 2.
We would like to remind you that the stove starting and switching off can be programmed four times in one day,
seven days in the week. The first cycle of starting/switching off takes place though the program 1, with presented
parameters
UT05
,
UT06
and
UT07
. Another cycle of starting/switching off take place through the program 2 and it
can be modified through the parameters
UT08
,
UT09
and
UT10
. The third program is performed with the
parameters
UT11
,
UT12
,
UT13
and the fourth program is performed through the parameters
UT14
,
UT15
and
UT16
.)
Once you adjust the starting time for the first program, use the button SET to move to parameter
UT06
, where you
can adjust the switching off time of the stove, again by using the buttons 1 and 2.
Once you confirm the selected switching off time by using the button SET, then you go to parameter
UT07
, where
you determine, that is, you set the days in the week when the previously defined program of starting / switching off
will be active, that is, when it will act.
Then the message "ON1" appears. This means than on day 1 (previously defined with the parameter
UT01
) the first
program of starting/switching off will be active i.e. it will act at that moment. In order to switch off the automatic
starting, switching off of the stove on that day, now press the button 2 and the display will show the message OFF1
(switched off programming for that day).
If instead of that you press the button 1, go to day 2 ("ON2") where in the same manner you can activate or switch
off the first starting program with button 2.
Continue in the same manner to activate/deactivate the programs for the remaining days in the week.
After programing the starting/switching off of the stove operation for different days in the week, once again press the
button SET in order to get access according to the sequence of parameters
UT08
,
UT09
and
UT10
, which
represent the parameters for adjusting another program for starting/switching off the stove, which can be
memorized.
In order to turn off, that is, to delete all weekly and daily programs for starting and switching off of the
stove for program 2 (when there is no more flickering of the UT parameter), press the button SET until UT10
appears on the display, than select OFF from the given selection by pressing the buttons 1 or 2 for all 7
days, separately for each day.
If you want to turn off, that is, to delete the programmed starting and switching off of the stove of the
program 1, you should press SET to get to UT07, for program 2 to get to UT12, for program 4 to get to UT16
and in the described manner as for program 2 (UT10) cancel all programs for starting and switching off of
the stove for all days (everywhere it should be OFF-switched off).
9.4 ALARM MANAGEMENT
An alarm signal (meaning that the stove informs about the occurrence of a certain problem with a sound signal)
appears in the following cases:
ORIGIN OF THE ALARM
INDICATION ON THE DISPLAY
Probe for smoke temperature
ALARM SOND FUMI
Probe for smoke temperature
ALARM HOT TEMP
Failed ignition
ALARM ACC NO
Stoppage of stove operation
ALARM NO FIRE
Lack of power supply
ALARM NO RETE
Safety pressure switch of the snail (spiral)
ALARM DEP NO
Thermostat for general safety
ALARM DEP NO
Pressure switch
ALARM DEP NO
In case of irregularities of the operation, the following procedure is activated:
1) The system for automatic pellet filling switches off
2) The smoke discharge fan operates with a full maximal capacity for maximum twenty minutes.
Before switching the stove once again, wait that it gets completely cold and then press the button „4“ (on/off).
If the stove is not cold, the message „
AttE
“ is shown as in figure 23.