manualshive.com logo in svg

Alfa Laval Tri-Clover 741 Series, Service & Installation Manual, Page: 9 / 34

Share
Download
Alfa Laval Tri-Clover 741 Series Service & Installation Manual Download Page 9

- 9 -

MAINTENANCE

VALVE COMPONENT INSPECTION

✓

✓

✓

✓

✓

VALVE BODY SEAT(s)

Inspect for nicks and scratches and other signs of excessive wear.  Leakage past

the seat(s) may result from these types of irregularities.

✓

✓

✓

✓

✓

VALVE STEM & SEAT(S)

Inspect rubber or PTFE seat(s) for signs of cracking, tearing, checking, or excessive

wear.  Note: Refer to the 

TR2-Seat Replacement section for installation of TR Seats.

Inspect stem finish for galling, nicks, or scratches.  Leakage may result from these
irregularities.

✓

✓

✓

✓

✓

SPLIT BUSHING

Inspect for signs of cracks, nicks, scratches or excessive wear on inside diameter.  A

worn bushing will not properly align valve stem.

✓

✓

✓

✓

✓

O-RING(S)

Inspect for cuts, abrasions, flat spots, or other damage that would cause leakage or
ineffective cleaning.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Tri-Clover 741 Series



































Reviews:

No comments