manualshive.com logo in svg

Alfa Laval Tri-Clover 741 Series, Service & Installation Manual, Page: 12 / 34

Share
Download
Alfa Laval Tri-Clover 741 Series Service & Installation Manual Download Page 12

- 12 -

MAINTENANCE

"TR & TR2" STEM/SEAT ASSEMBLY

REMOVAL OF PTFE SNAP-ON SEAT

1.

Refer to valve disassembly section to remove stem / seat assembly
from valve.

2.

Using a knife, partially cut through the upper ring portion of Snap-On
Seat, avoiding contact with stainless steel stem.  Grasp both cut
ends of Snap-On Seat and force apart for removal from Stem. Since
there are no slots, the TR2 seat will require cutting through sides and
base of seat.

INSTALLATION OF REPLACEMENT PTFE SNAP-ON SEAT

Tri-Clover’s replacement Snap-On Seats do not require heat or special
tools for proper installation.  Snap-On Seats are installed by applying
uniform pressure on all sides.  Pressure can be applied by using a Tri-
Clamp or Bevel Seat ferrule the same size as the valve.

Due to the greater force required to instal the TR2 style seat, we
recommend using a TR2 seat tool. This holds the seat more
securely and can also be used on standard TR seat installation.

See parts list for tool numbers

.

SHUT OFF VALVE OR LOWER SEAT OF DIVERT VALVE

1.

Place Snap-On Seat on the lower portion of the stem.

2.

Place assembly from Step 1 on Tri-Clamp or Bevel Seat ferrule,
resting on a hard flat surface such as a bench or table.

3.

Apply firm even downward pressure on the stem until the Snap-On
Seat hits the shoulder of the stem and snaps into place.

4.

Examine seat assembly to be sure each individual tab is secure
under the smaller lip portion of the stem.  Press tabs down with your
fingers or a straight edge.  Holding Stem/Seat Assembly in one hand,
rotate the Snap-On Seat.  For proper CIP cleaning the seat should
turn freely on the stem.

5.

Refer to valve assembly section for reassembly.

UPPER SEAT OF DIVERT VALVE

1.

Place Snap-On Seat on the upper portion of the stem.

2.

Place Tri-Clamp or Bevel Seat ferrule on top of assembly, resting on
a hard, flat surface such as a bench or table.

3.

Apply firm, even, downward pressure of Tri-Clamp or Bevel Seat
ferrule until Snap-On Seat hits the shoulder of the stem and snaps
into place.

4.

Examine Seat Assembly to be sure individual tab is secure under the
smaller lip portion of the stem.  Press tabs down with your fingers or a
straight edge.  Holding Seat Assembly in one hand, rotate the Snap-
On Seat.  For proper CIP cleaning, seat should turn freely on the
Stem.

5.

Refer to valve assembly section for assembly.

Cut here

to remove

seat.

Lip

Straight
Edge

Push Tab Here Up

Tri-Clamp or Bevel Seat

Ferrule to be same size

as valve

Shoulder

Lower Portion

Tri-Clamp or Bevel Seat

Ferrule to be same size

as valve

Upper Portion

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Tri-Clover 741 Series



































Reviews:

No comments