Alfa Laval TE20B200 Instruction Manual Download Page 25

 

Instruction Manuall Toftejorg SaniJet 20 Electrically Driven 

Page 23 

IM-TE91A794-EN6 

Operation 

Normal Operation 

Pressure 

In order to protect the machine, your pipe and valve installation, etc. against damage: 

 

Avoid hydraulic shocks! Put on pressure gradually! 

 
Recommended working pressure: 5 - 8 bar (75 - 115 psi). Too high pressure will increase consumption 
of wear parts. 
 
The machine is designed to stand up to 13 bar working pressure. This is normally not recommended 

but may be used for special purposes, where high pressure at close distance is preferred. 
 

Cleaning Media 

Use only cleaning fluids, which are compatible with Stainless Steel AISI 316/316L, SAF2205, Titanium 

Grade 5, Hastelloy C22/C276, PEEK, E-CTFE, EPDM and Viton.  Normal detergents, moderate 
solutions of acids and alkalics are acceptable as well as a number of solvents at ambient temperature 
during cleaning. Aggressive chemicals, excessive concentrations of chemicals at elevated 
temperatures as well as certain solvents and hydrochlorides should be avoided. If you are in doubt, 

contact your local Alfa Laval Tank Equipment sales office. 
 

Temperature 

The machine is designed to operate with cleaning media at temperatures up to 90°C (194 °F). 

However, it stands temperatures up to 140°C (284°F) inside the tank, and it is possible to steam the 
tank through the machines. 
 
The machine is not designed to rotate during steaming. A slow rotation  of the media driven machine 
might occur and is not harmful. The air or electric motor must not be running during steaming. 

 

Warning: 

Tanks with capacities greater than 100 m

3

 that could contain a flammable atmosphere 

should not be steam cleaned, as steam issuing from a nozzle could contain charged 

droplets.  

Tanks smaller than this may be steam cleaned providing that: the steam nozzles and 
other metal parts of the system are reliably earthed and grounded to the tank 
structure. 

 

 

Warning: 

In potentially explosive atmospheres, the temperature must not exceed the maximum 

surface temperature according to the temperature class for the combustible gas or 
liquid.  

 

 

Summary of Contents for TE20B200
















































Reviews: