background image

1. Turn on the valve on the gas supply cylinder completely.
2. Press and turn the variable control knob to PILOT position (counter-clockwise 90º).
3. Press down the variable control knob and hold for 30 seconds. While holding down the variable control knob, 
press the igniter button several times until the pilot flame lights. Release the variable control knob after the pilot 
flame lights.

1. Turn the variable control knob to PILOT position.
2. Press and turn the variable control knob to OFF position.

1. Always close the gas valve of the gas cylinder after use or in case of a disturbance
2. Remove the pressure regulator and the hose.
3. Check the tightness of the gas valve for damage. If you suspect damage, have it changed by your gas dealer.
4. Never store liquid gas cylinder in a sub-terrain, or at places without adequate air ventilation.

•  Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible 

or corrosive.

• Remove debris from the burner to keep it clean and safe for use.
• Cover the burner unit with the optional protective cover when the heater is not in use.

3. Turn off the valve on the gas supply cylinder completely.

4.  After the pilot flame lights, turn the variable control knob to maximum position and leave it there for 5 minutes 

or more befor turning the knob to desired temperature position.

Note:
•  If a new tank has just been connected, please allow at least one minute for the air in the gas pipeline 

to purge out through the pilot hole.

•  When lighting the pilot flame make sure that the variable control knob is continuously pressed down 

while pressing the igniter button. Variable control knob can be released after the pilot flame lights.

• If the pilot flame does not light or goes out, repeat step 3.

WARNING

Check that no broken glass is found before 
operation.

lgniter

Igniter

Variable control knob

Off: turn heater off 
Hi: maximum temperature position  
Lo: minimum temperature position

Operating & Storage

TO TURN ON THE HEATER

TO TURN OFF THE HEATER

STORAGE

CLEANING AND CARE

Summary of Contents for PYRAMID SQUARE















Reviews: