background image

Australian Communications Media Authority 

(ACMA)

This device is classified as a low risk device in 

accordance with the ACMA labelling framework and 

as described under Radiocommunications Labelling 

(Electromagnetic Compatiblity) Notice 2017. The 

ACMA only mandates performance requirements 

in relation to emissions therefore compliance to the 

listed standards is only required to the extent that 

relate to interference to:

1.  Radiocommunications
2.  Any uses or functions of devices

Accordingly, this device was tested to the UN ECE 

R10 standard that pertains to the uniform provisions 

concerning the approval of vehicles with regard to 

electromagnetic compatibility and was determined to 

meet that standard.

Federal Communications Commission (FCC) 

Disclaimer

Changes or modifications not expressly approved by 

the party responsible for compliance could void the 

user’s authority to operate the equipment.
To comply with Radio Frequency (RF) exposure 

requirements, a separation distance of at least 20 cm 

must be maintained between the antenna(s) of the 

Electronic Control Unit (ECU) and all persons.
This device complies with Part 15 of the FCC rules. 

Operations are subject to the following 2 conditions:

1.  This device may not cause harmful interference
2.  This device must accept any interference 

received, including interference that may cause 

undesired operations

Industry Canada / Industrie Canada
This device contains licence - exempt transmitter(s) / 

receiver(s) that comply with innovation. Science and 

Economic Development Canada’s license - exempt 

RSS(s)
This device may not cause interference, and 
This device must accept any interference, including 

interference that may cause undesired operation of 

the device.

L’émetteur/récepteur exempt de licence contenu 

dans le présent appareil est conforme aux 

CNR d’Innovation, Sciences et Développement 

économique Canada applicables aux appareils radio 

exempts de licence. 
L’appareil ne doit pas produire de brouillage, et 
L’utilisateur de l’appareil doit accepter tout brouillage 

radioélectrique subi, même si le brouillage est 

susceptible d’en compromettre le fonctionnement.

Summary of Contents for LR max
















Reviews: