manualshive.com logo in svg

Alcatel-Lucent ALE M3, Administrator'S Manual, Page: 104 / 227

Share
Download
Alcatel-Lucent ALE M3 Administrator'S Manual Download Page 104

 

ALE M3-M5-M7-M8 DeskPhones Administrator Guide

                                              

 

104 

Parameter 

FeatureCallNumberFilter 

config.xml 

Description 

It configures the characters that the IP phone will filter when dialing. 
If the dialed number contains configured characters, the IP phone will 
automatically filter these characters when dialing. 
If you dial 10-1, the IP phone will filter the character - and then dial out 101. 

Permitted 
Values 

String within 32 characters 

Default 

,-() 

Web UI 

Setting 

→

 General 

→

 Call Number Filter 

10.10 IP Address Call 

You can configure the phone whether to receive or place an IP call.  

10.10.1 IP Address Call Configuration

 

The following table lists the parameter you can use to configure an IP address call. 

Parameter 

SIPIpCallEnable 

config.xml 

Description 

It enables or disables IP address call feature.  

Note:

 The parameter can only control the outgoing IP address call. If you don't want 

to answer the IP address call, you should set the parameter "SIPIpCallEnable" to 
false. 

Permitted 
Values 

true - enable 
false - disable 

Default 

false 

Web UI 

SIP Features 

→

 SIP 

→

 Allow IP Call 

10.10.2 Accept SIP Trust Server Only Configuration 

Accept SIP Trust Server Only enables the IP phone to only accept the SIP messages from your SIP server 
and outbound proxy server. It can prevent the phone from receiving ghost calls from random numbers. If you 
enable this feature, the IP phone cannot accept an IP address call. 

The following table lists the parameters to configure the Accept SIP Trust Server Only feature. 

Parameter 

SIPPeerFilterEnable 

config.xml 

Description 

It enables or disables filtering the IP address call. 

Note:

 The parameter can only control the incoming IP address call. If you want to 

make an outgoing IP address call, you should set the parameter "SIPIpCallEnable" to 
true. 

Permitted 
Values 

true - enable 
false - disable 

Default 

false 

Summary of Contents for ALE M3




































































































































































































































Reviews:

No comments