background image

 
Alcatel-Lucent 4080 IP-DECT  

Installation Manual 

 

 

8AL90850USAAed01 

 

 

Regulatory information European Union 

Declaration of Conformity 

This equipment is in compliance with the essential requirements of R&TTE 
Directive 1999/5/EC.The Declaration of Conformity may be obtained from your 
installer. 

PRODUCT DISPOSAL INFORMATION (EN) 

For countries in the European Union 

The symbol depicted here has been affixed to your product 
in order to inform you that electrical and electronic 
products should not be disposed of as municipal waste. 

Electrical and electronic products including the cables, plugs and 
accessories should be disposed of separately in order to allow proper 
treatment, recovery and recycling. These products should be brought to 
a designated facility where the best available treatment, recovery and 
recycling techniques is available. Separate disposal has significant 
advantages: valuable materials can be re-used and it prevents the 
dispersion of unwanted substances into the municipal waste stream. 
This contributes to the protection of human health and the environment. 

Please be informed that a fine may be imposed for illegal disposal of electrical and 
electronic products via the general municipal waste stream. 

In order to facilitate separate disposal and environmentally sound recycling arrangements 
have been made for local collection and recycling. In case your electrical and electronic 
products need to be disposed of please refer to your supplier or the contractual 
agreements that your company has made upon acquisition of these products.  

For countries outside the European Union

 

Disposal of electrical and electronic products in countries outside the European Union 
should be done in line with the local regulations. If no arrangement has been made with 
your supplier, please contact the local authorities for further information. 

Summary of Contents for 4080 IP-DECT





























Reviews: