Albixon ELEGANCE 70, Manual

Page: 23 / 84

PIC. 2a PIC. 2b
PIC. 2c PIC. 2d
INSTALLATION IN CONCRETE
SWIMMING POOLS
INSTALLATION IN CONCRETE
SWIMMING POOLS WITH LINER
INSTALLATION IN PANEL
OR SHEET METAL
SWIMMING POOLS WITH LINER
INSTALLATION IN PREFABRICATED
(LAMINATE OR POLYPROPYLENE)
SWIMMING POOL
POOL WALL
APERTURE
(Ø 270 mm)
SEALING no. 18 (another
seal may be done from
the other side of the liner)
CONCRETE
POOL
CONCRETE
LINER
APERTURE
(Ø 270 mm)
PANEL OR SHEET METAL
APERTURE (Ø 270 mm)
LINER
4
/ Swim jet ELEGANCE 70
Installing the swim jet body
3.1 Installing the swim jet body in concrete
Stick hoses (no. 21 pic. 3) on the swim jet body (no. 20 pic. 3) and connect them into the technology
device area (pit). Protect the hose endings against the concrete. Carry out the swim jet body installation
(no. 20 pic. 3) as indicated in pic. 2a into the hole made in the concrete wall or into the formwork for
concreting without a flange or sealing. When the body is fixed to the wall, follow the instructions in
section 4 and install the pneumatic and air connections.
3.2 Installation of swim jet device body in concrete pools with liner
While mounting the swim jet body into the walls of a concrete pool with liner, please follow the
instructions written in chapter no. 2 and 3. You can start mounting the sealing and the swim jet flange
(pic. 2b) into the pool after fixing the swim jet body onto the wall of the pool. 2b.
Tighten the sealing (no. 18 in pic. 3) into the swim jet body (no. 20 in pic. 3) with 2 screws (no. 19 in pic.
3) and bear in mind that the pool liner can be situated between two seals (pic. 2b). Finally, fix the flange
(no. 17 in pic. 3) and tighten the screws (no. 16 in pic. 3), after this step is done, cut the liner from the
inside part of the flange. During the installation of the air and pneumatic lines, follow the procedure
in article 4.
3.3 Installation of swim jet device body in panel or sheet metal pools with liner
Prepare the opening of 270 mm diameter in the wall pool so that the centre of the jet is approximately
30cm under the water level as described in the article 2 (pic. 1). Place the swim jet body (no. 20 in pic. 3)
from the inside part of the pool into the prepared opening. Fix the body with 8 self-drilling screws (no.
19 in pic. 3) into the wall of the pool as described in pic. 2c. Tighten the sealing (no. 18 in pic. 3) to the
swim jet body (no. 20 in pic. 3) with 2 screws (no. 19 in pic. 3). After the installation of the liner, fix the
flange (no. 17 in pic. 3) and tighten the screws (no. 16 in pic. 3), then cut the liner from the inside part of
the flange. During the installation of the air and pneumatic lines, follow the procedure in article 4.
3.4 Installation of the swim jet body to the preformed (polypropylene) pool
Prepare the opening of 230 mm diameter in the pool wall so that the centre of the jet is approximately
30cm under the water level as described in the article 2 and pic. 1. Stick the sealing (no. 18 in pic. 3)
from the inside part of the pool wall and prepare openings for the 16 screws of the flange (no. 16 pic.
3). Prepare the swim jet body (no. 20 pic. 3) from the inside part of the pool and tighten the flange
(no. 17 in pic. 3) with screws (no. 16 in pic. 3) from the inside part as described in pic. 2d. During the
installation of the air and pneumatic lines, follow the procedure in article 4.
Installation of the swim jet body to a prefabricated pool
Installation of the swim jet body to a prefabricated pool should be carried out in compliance
with the pool manufacturer. The mounting may differ from the recommendations of the swim jet
manufacturer. It may also be in a different location according to the individual types and dependent
on the design of the swimming pool.
3.
Swim jet ELEGANCE 70 /
5
ELEGANCE 70 / 80 / 95 |
21