Albatron KM51PV-754 User Manual Download Page 6

Page: 6 / 54

Mainboard KM51PV-754

Specification

CPU:

Supports Socket 754

Supports AMD Athlon

64/ Sempron

Processor

Supports

Hyper-Transport

Link Technology

Supports 800 MHz (1600MT/s) FSB (Front Side Bus) Frequencies

Chipset:

Northbridge Chipset – nVIDIA

nForce4 C51PV ( nVIDIA

GeForce

6150)

－

Integrated nVIDIA

Pure Video

Technology

－

Supports TV Encoder

－

Supports 475 MHz Graphic Clock

－

Supports MPEG-2 (DVD)/ WMV9 (HD-Video) Playback

－

Supports Video Scaling

Southbridge Chipset – nVIDIA

nForce4 MCP51 ( nVIDIA

nGorce 430)

I/O Controller – Winbond

W83627HF-AW

AC’ 97 Aduio Codec – Realtek

ALC655

LAN PHY Controller – Broadcom

AC 131

Memory:

Two DIMM sockets with Dual Channel Technology supported, and also support a

total memory capacity of 2GB

Supports to use 184-pin, non-ECC, and unbuffered DDR400 (PC3200)/ DDR333

(PC2700)/ DDR266 (PC2100) SDRAMs

Slots:

One PCI-E x16 slot

One PCI-E x1 slot

Two PCI slots

FDD Connector:

One floppy disk drive connector, supports up to two FDDs can be set

Supports

360KB/720KB/1.2MB/1.44MB/2.88MB

Summary of Contents for KM51PV-754























































Search results

Summary of Contents for KM51PV-754

Reviews:

Related manuals for KM51PV-754

Brands by name

Popular brands

Albatron KM51PV-754, User Manual

Search results

Summary of Contents for KM51PV-754

Reviews:

Related manuals for KM51PV-754

Brands by name

Popular brands