Albatron K8NF4X-AM2 User Manual Download Page 6

Page: 6 / 32

Mainboard K8NF4X-AM2

Specification

CPU:

Supports

Socket

AM2

Supports

AMD

Athlon

64 FX/ Athlon

64 x2 Dual-Core/ Athlon

64/ Sempron

Processor

Supports

Hyper-Transport

Link Technology

Supports 800MHz/ 1000 MHz (by overclocking) FSB (Front Side Bus) Frequencies

Chipset:

Chipset – nVIDIA

nForce4 4X

I/O Controller – Fintek

F71872FG

AC’ 97 Aduio Codec – Realtek

ALC655

LAN PHY – Realtek

RTL8201CL 10/100 LAN PHY

Memory:

Two DIMM sockets with Dual Channel Technology supported

Supports a total memory capacity of 4GB

Supports to use the 240-pin, non-ECC & unbuffered DDR II 800/ 667/ 533/ 400

SDRAM

Slots:

Two PCI-Express interface slots for graphics cards and expansion cards:

1. PCI-E x16 slot: Supports up to x16 mode with 4 GB/s one-way bandwidth
2. PCI-E x1 slot: Supports up to x16 mode with 250 MB/s one-way bandwidth

Four PCI slots with 133 MB/s one-way bandwidth per channel for expansion cards

FDD Connector:

One floppy disk drive connector supporting up to two FDD

Supports 360KB/ 720KB/ 1.2MB/ 1.44MB/ 2.88MB

Onboard IDE Connector:

Two IDE connectors that support up to four IDE devices

Supports Ultra ATA 133/ 100/ 66/ 33

Summary of Contents for K8NF4X-AM2

































Search results

Summary of Contents for K8NF4X-AM2

Reviews:

Related manuals for K8NF4X-AM2

Brands by name

Popular brands

Albatron K8NF4X-AM2, User Manual

Search results

Summary of Contents for K8NF4X-AM2

Reviews:

Related manuals for K8NF4X-AM2

Brands by name

Popular brands