Albatron K8NF4X-AM2 User Manual Download Page 19 | Manualshive

Page: 19 / 32

background image

Mainboard K8NF4X-AM2

15

AUDIO

Pin

Assignment

Pin

Assignment

1 AUD_MIC

2 AUD_GND

3 AUD_MIC_BIAS

4 AUD_VCC

5 AUD_FPOUT_R

6 AUD_RET_R

7 HP_ON

8 N/A

9 AUD_FPOUT_l

10 AUD_RET_L

Slots

PCI-Express x1 Slot: PE1

This mainboard is able to install an expansion card which the PCI-Express x1 interface

compatible such as network card, SCSI card, etc. to this PE1 slot.

PCI-Express x16 Slot: PE2

This mainboard is able to install a graphics card, which the PCI-Express x16 interface,

supporting one-way bandwidth up to 4 GB/s, is compatible to this PE2 slot.

PCI Slots: PCI1/2/3/4

PCI stands for Peripheral Component Interconnect and is a bus standard for installing

expansion cards such as network card, SCSI card, etc. to these PCI slots.

«
...
17
18
19
20
21
...
»

Summary of Contents for K8NF4X-AM2

































Reviews:

No comments

Related manuals for K8NF4X-AM2

Brand: ECS Pages: 27

ASC Bridge Board

Brand: Lattice Semiconductor Pages: 25

Brand: ZiLOG Pages: 41

Brand: IBASE Technology Pages: 65

Brand: JETWAY Pages: 49

Brand: Linear Technology Pages: 7

Brand: Supero Pages: 101

Brand: Energy Pages: 14

MPG Z390 GAMING EDGE AC

Brand: MSI Pages: 87

Brand: BCM Pages: 93

Brand: Gigabyte Pages: 37

Brand: MSI Pages: 85

Brand: Gigabyte Pages: 36

Brand: Pure Photonics Pages: 11

Brand: Gigabyte Pages: 72

Brand: Alinx Pages: 29

Brand: Raisonance Pages: 46

Brand: Supermicro Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands